Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item Optical and electrical properties of ITO thin films sputtered on flexible FEP substrate as passive thermal control system for space applications(Elsevier, 2016) Sibin, K.P.; Swain, N.; Chowdhury, P.; Dey, A.; Sridhara, N.; Shashikala, H.D.; Sharma, A.K.; Barshilia, H.C.ITO thin films were deposited on flexible fluorinated ethylene propylene (FEP) substrates by pulsed direct current reactive magnetron sputtering system using an In:Sn (90%-10% wt.) alloy target. The influence of the deposition parameters (argon and oxygen flow rates, and substrate temperature) and effect of coating thickness on the optical, electrical, structural and microstructural properties of ITO thin films deposited on FEP was investigated. The thickness of the ITO coatings was varied from 5 to 180 nm. The optimized ITO coating (10 nm thick) exhibited high IR emittance (79%) on FEP substrate with high average solar transmittance (94.0%) and moderate sheet resistance (3 k?/sq.). We also investigated in detail the angular dependence of reflectance as well as haze factor of thin ITO coatings. Our results suggest that 10 nm thick ITO coating exhibits an average haze factor of 8.6%. The high value of IR emittance, moderate sheet resistance and high solar transmittance along with low haze factor indicate the suitability of ITO thin films on FEP substrates as flexible optical solar reflector for space applications. © 2015 Elsevier B.V. All rights reserved.Item Design and development of ITO/Ag/ITO spectral beam splitter coating for photovoltaic-thermoelectric hybrid systems(Elsevier Ltd, 2017) Sibin, K.P.; Selvakumar, N.; Kumar, A.; Dey, A.; Sridhara, N.; Shashikala, H.D.; Sharma, A.K.; Barshilia, H.C.ITO/Ag/ITO (IAI) multilayer coatings were designed for spectral beam splitter applications and these coatings were deposited on glass substrates by magnetron sputtering method. The thicknesses of the component layers, namely, Ag and ITO were varied to achieve high visible transmittance, high NIR-IR reflectance and optimum cut-off wavelength. The optimized ITO/Ag/ITO exhibits high visible transmittance (?88%) and high NIR-IR reflectance (>90%) with an optimum cut-off wavelength (?900 nm). A novel chemical etching method was used to improve the transmittance of the plain glass substrate. The optimized IAI multilayer coating deposited on single side etched glass substrate resulted in increase in transmittance (?91%), which is due to the nano-porous morphology of the etched glass substrate. The angular and polarization dependence studies of IAI multilayer coatings were also studied in detail. © 2016 Elsevier LtdItem Optical properties of TiAlC/TiAlCN/TiAlSiCN/TiAlSiCO/TiAlSiO tandem absorber coatings by phase-modulated spectroscopic ellipsometry(Springer Verlag service@springer.de, 2017) Jyothi, J.; Biswas, A.; Sarkar, P.; Soum-Glaude, A.; Nagaraja, H.S.; Barshilia, H.C.TiAlC, TiAlCN, TiAlSiCN, TiAlSiCO, and TiAlSiO layers of thicknesses ~2.2 ?m, 755, 491, 393, and 431 nm, respectively, were deposited on stainless steel, silicon, and glass substrates to study their refractive indices and extinction coefficients using the phase-modulated spectroscopic ellipsometry in the wavelength range of 300–1200 nm. Absorption coefficient of each layer was calculated from the extinction coefficient of the layer. The results indicate that the first three layers (i.e., TiAlC, TiAlCN, and TiAlSiCN) are absorbing in nature, while TiAlSiCO and TiAlSiO act as intermediate and antireflection layers. Subsequently, a tandem absorber of TiAlC/TiAlCN/TiAlSiCN/TiAlSiCO/TiAlSiO with layer thicknesses of 62, 20, 18, 16, and 27 nm, respectively, was deposited on stainless steel substrates to fabricate a spectrally selective coating with absorptance of 0.961 and emittance of 0.15 at 82 °C. The obtained refractive indices and extinction coefficients of the tandem absorber were used to simulate the reflectance of the deposited tandem absorber using SCOUT software. Simulated reflectance data of the tandem absorber showed a good agreement with the experimental data measured by UV–Vis–NIR and FTIR spectrophotometry. The angular dependence of the selective properties of the tandem absorber was studied by measuring the reflectance spectra of the tandem absorber at different incident angles. © 2017, Springer-Verlag GmbH Germany.Item Measurement of high temperature emissivity and photothermal conversion efficiency of TiAlC/TiAlCN/TiAlSiCN/TiAlSiCO/TiAlSiO spectrally selective coating(Elsevier B.V., 2017) Jyothi, J.; Soum-Glaude, A.; Nagaraja, H.S.; Barshilia, H.C.A spectrally selective TiAlC/TiAlCN/TiAlSiCN/TiAlSiCO/TiAlSiO coating was deposited on stainless steel substrate by unbalanced magnetron sputtering system. Each individual layer of the tandem absorber was optimized by varying the reactive gas flow rates (C2H2, N2 and O2) and target power densities (Ti, Al and Si). The optimized tandem absorber shows a solar absorptance of 0.960 and an emittance of 0.15 at 82 °C, measured using solar spectrum reflectometer and emissometer, respectively. In order to study the optical properties of the deposited tandem absorber at high operating temperatures the reflectance spectra of the tandem absorber were measured at temperatures ranging from 80 °C to 500 °C by UV–Vis–NIR spectrophotometer and FTIR spectrometers. The reflectance spectra of the as-deposited sample and after high temperature reflectance measurements did not show any significant changes. The thermal emittance of the tandem absorber at high temperatures (80–500 °C) was studied in detail. At the temperature of 200 °C, 300 °C, 400 °C and 500 °C the tandem absorber shows the emittance of 0.152–0.157, 0.181–0.19, 0.214–0.246 and 0.251–0.275, respectively with an absorptance of ~0.930. These results show the good selectivity of the tandem absorber even at high operating temperatures (e.g., 500 °C) with a photothermal conversion efficiency of 88%, thus demonstrating that the tandem absorber is suitable for solar thermal power generation applications. Reflectance and roughness data of the absorber coating post annealing in air up to 600 °C for 2 h, carried out independently, corroborated the present results. © 2017 Elsevier B.V.Item Highly transparent and conducting ITO/Ag/ITO multilayer thin films on FEP substrates for flexible electronics applications(Elsevier B.V., 2017) Sibin, K.P.; Srinivas, G.; Shashikala, H.D.; Dey, A.; Sridhara, N.; Sharma, A.K.; Barshilia, H.C.Transparent and conducting ITO/Ag/ITO (IAI) multilayer coatings were deposited on glass and flexible fluorinated ethylene propylene (FEP) substrates by reactive sputtering using metallic In:Sn (90%:10%) and Ag targets at room temperature. Middle Ag layer thickness was optimized to obtain maximum figure of merit (?) and the optimum Ag layer thickness was found to be ~13 nm. The optimized IAI multilayer on glass substrate showed transmittance of ~88.6% and sheet resistance of ~7.1 ?/sq. The transmittance increased to ~91.4% for the IAI multilayer deposited on one side etched glass. The optimized IAI multilayer coating was also deposited on flexible FEP substrates. The electrical, optical, structural and morphological properties of IAI deposited on glass and FEP substrates were compared. IAI deposited on FEP substrate showed transmittance of ~90.2% at ? = 550 nm, sheet resistance of ~6.9 ?/sq. and figure of merit of ~52 × 10?3 ??1. Bending test of IAI deposited FEP proved the high flexibility of IAI multilayer for the flexible transparent electrode applications. Solar selectivity study of IAI on FEP substrate showed it can effectively reflect the higher wavelength region of solar spectrum and can be used as a flexible solar spectrum segregator. Optical haze measurements of IAI coated glass and FEP show that high haze value can be achieved by increasing the roughness on non-coated side of the FEP substrate. © 2017Item Environmental stability of transparent and conducting ITO thin films coated on flexible FEP and Kapton® substrates for spacecraft applications(Elsevier B.V., 2018) Sibin, K.P.; Mary Esther, A.C.; Shashikala, H.D.; Dey, A.; Sridhara, N.; Sharma, A.K.; Barshilia, H.C.Acquiring good adhesion of ITO thin films on polymer substrate is a major concern, especially for space related applications. Delamination of ITO coating on these polymers can seriously damage the spacecraft. This paper presents the development of highly transparent and conducting ITO thin films on as-received and surface treated fluorinated ethylene propylene (FEP) and Kapton® substrates by reactive direct current magnetron sputtering. Stability of the ITO coating on FEP and Kapton® substrates was studied in simulated space environments. Environmental tests such as: relative humidity, thermal cycling and thermo vacuum were performed. Thermo-optical properties and sheet resistance of ITO coated FEP and Kapton® substrates were studied before and after environmental tests. Optimized ITO coating with thickness of ~ 15 nm on FEP and Kapton® substrates showed sheet resistance in the range of 2–4 k?/sq. with high average transmittance and high IR emittance. Adhesion of ITO coating on FEP substrate was improved by Ar plasma etching. X-ray photoelectron spectroscopy and field emission scanning electron microscopic studies of etched FEP substrate showed defluorination and high roughness of the etched surface which helped for better adhesion of ITO coating. We demonstrated that ITO coated plasma etched FEP substrate showed no change in the sheet resistance and thermo-optical properties. Moreover, ITO coated etched FEP substrate showed good environmental stability than ITO coated untreated FEP substrates. © 2017 Elsevier B.V.