Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
5 results
Search Results
Item A study on the effect of process parameters and scan strategies on microstructure and mechanical properties of laser directed energy deposited IN718(Elsevier Ltd, 2023) Thanumoorthy, R.S.; Sekar, P.; Bontha, S.; Balan, A.S.S.The present study focuses on understanding the effect of scan strategy on the microstructure and mechanical properties of LDED fabricated IN718 built at optimized process conditions from single track analysis. Initially, single track studies were conducted by varying laser power, scan speed, and feed rate (3 levels) to optimize process parameters for bulk deposition. Based on the dilution, aspect ratio, track continuity and melt pool shape, best process parameter were chosen for depositing bulk structures. Bulk rectangular specimens were fabricated using the LDED process for different infill rotation (0°, 45°, 67°, and 90°) at optimized process conditions. Infill rotation did not show any significant change in the density of the samples. However, grain size measurement from EBSD and SEM micrographs revealed a substantial difference in grain size between samples without infill rotation (0°) and samples with infill rotation (45°, 67°, and 90°). XRD and EDS mapping revealed higher the formation of secondary laves phases with infill rotation as a result of higher cooling rate. Similarly, melt pool shape and arrangement showed significant variation with different infill angles. Samples with 0° and 90° infill rotation exhibited strong crystallographic texture along the build direction. There was a significant variation in the microhardness and tensile strength of the build with variation in infill rotation. This variation in mechanical properties were attributed to grain size, LAGB's fraction, secondary phases, and crystallographic texture. © 2023 Elsevier B.V.Item Effect of equiaxed grains and secondary phase particles on mechanical properties and corrosion behaviour of CMT- based wire arc additive manufactured AZ31 Mg alloy(Elsevier Ltd, 2023) Manjhi, S.K.; Sekar, P.; Bontha, S.; Balan, A.S.S.Wire arc additive manufacturing (WAAM) has drawn tremendous attention for manufacturing large and complex components of lightweight material at a moderate cost due to its high deposition rate and energy efficiency. Generally, WAAM-Mg alloy comprises columnar and columnar dendrite grains due to high cooling rates and thermal gradients responsible for anisotropic mechanical properties. To overcome this challenge, in this work, CMT-WAAM, which generally uses comparatively low heat input (33% lower than conventional WAAM), was used to deposit AZ31 Mg thin wall. The metallurgical characterization of the deposited thin wall of the top (T), middle (M) and bottom (B) sections reveals equiaxed grains of average sizes ∼ 58, ∼ 63 and ∼ 38 µm, respectively. In addition, TEM results exhibit the formation of secondary phase particles, i.e., β-Mg17Al12 and ɳ-Al8Mn5. Further, the ultimate tensile strength (UTS) and % elongation (% EL) in the travel direction (UTS = 224 MPa, % EL= 23.47%) are superior to that obtained in the build direction (UTS = 217 MPa, % EL = 20.82%). The corrosion resistance of WAAMed AZ31 Mg alloy is higher than wrought (cold rolled) AZ31 Mg alloy in Hank's balanced salt solution (HBSS). The results of this study reveal the potential of CMT-WAAM to deposit different grades of Mg with desired microstructure, mechanical properties and corrosion resistance. © 2023 CIRPItem Hybrid additive manufacturing of ER70S6 steel and Inconel 625: A study on microstructure and mechanical properties(Elsevier Ltd, 2023) Rodrigues, J.P.; Thanumoorthy, R.S.; Manjhi, S.K.; Sekar, P.; Arumuga Perumal, D.A.; Bontha, S.; Balan, A.S.S.Hybrid Additive Manufacturing (HAM) is currently being explored because of its potential to achieve trade-off between build capacity and feature resolution. The present study aims at fabricating ER70S6-Inconel 625 (IN625) bimetallic clad using hybrid Wire Arc Additive Manufacturing (WAAM) and Laser Directed Energy Deposition (LDED) processes. Microstructure evaluation was performed at the cross section of bimetallic clad for distinct materials as well as the interface. WAAM built ER70S6 revealed equiaxed ferritic grains, whereas laser deposited IN625 region showed columnar dendrites with under developed secondary arms. However, the first layer of IN625 exhibited columnar dendrite with secondary arms due to the influence of diffused Fe from the base ER70S6 steel under the action of concentrated laser heat source, which was revealed by energy dispersive spectroscopy (EDS) maps. The measured microhardness across the cross section of the deposit showed values corresponding to inherent material system. The interface did not reveal presence of any intermetallic phases which was confirmed by hardness results and X-Ray diffraction. Shear test revealed superior bond strength between the two materials, maintaining average strength of 452 MPa. The fractography images exhibited fine dimples along with cleavages indicating mixed fracture characteristics. This additive manufacturing method explores a new dimension in multi-material fabrication which, when customized for different materials, serve critical areas in the aerospace and defence sector. © 2023 Elsevier LtdItem Effect of Wire-EDM textures on corrosion performance of Bio-Degradable Mg alloy(Elsevier B.V., 2024) Aswith Babu, I.; Kumar Manjhi, S.; Sekar, P.; Narendranath, S.; Balan, A.S.S.Magnesium (Mg) is the most suitable material for biodegradable implant applications owing to its nontoxic behaviour and comparable Young's modulus to human bone. However, poor corrosion resistance limits its application. Therefore, surface texturing can be a more suitable and cost-effective technique to mitigate these issues. Hence, wire electric discharge machining (WEDM) is used to create various textures (wavy texture, microchannels, and micro-pillars) and investigate their influence on the corrosion resistance of Mg-Zn-Ca alloy. The results revealed that micropillar texture exhibited significantly lower surface roughness (Ra = 1.049 µm) and a higher contact angle indicative of hydrophobicity (130.3°), resulting in superior corrosion resistance (corrosion rate: 0.816 mm/year) compared to other textures and standard WEDM surfaces. These findings suggested that textured surfaces generated through WEDM hold the potential for enhancing the corrosion resistance of biodegradable Mg implants. © 2024 Elsevier B.V.Item Investigating the role of WEDM surface texturing in the degradation and biocompatibility of Mg–Zn–Ca alloy(KeAi Publishing Communications Ltd., 2025) Aswith Babu, I.; Sekar, P.; Prabhu, A.; Narendranath, S.; Balan, A.S.S.Magnesium (Mg) alloy-based biodegradable implants are gaining popularity for their low density, high strength, and biocompatibility. The corrosion and wear performance of Mg is poor in physiological environments, leading to premature failure. Surface modification, particularly through surface texturing, reduces the effective contact area of Mg–Zn–Ca alloy with corrosive media and tribological partners, potentially optimizing its degradation kinetics and cytocompatibility. Wire Electric Discharge Machining (WEDM) offers a stable oxide layer on the surface, unlike laser surface texturing, which may thermally damage the Mg alloy. In this study, three types of textures, mainly Wavy Texture (WT), microchannels (MC), and micropillars (MP), were created using WEDM on the Mg–Zn–Ca samples, and their corrosion, wear, cytotoxicity, and cell adhesion performance were evaluated. Texturing on the surface of the samples enhanced the corrosion performance, from 3.14 mm/year for the untextured sample to 0.98 mm/year for the micropillar textured sample, representing a 68.8 % reduction. This improvement after texturing is attributed to the superior surface finish (1.049 ?m) and increased hydrophobicity (130.3°), equating to a 50.8 % improvement. The coefficient of friction (COF) value decreased from 0.364 for an untextured sample to 0.208 for microchannels, a 42.9 % reduction, due to the entrapment of debris in the textures and effective heat transfer. The samples' cell adhesion and cell viability have been improved after texturing. The combination of cytocompatibility, appropriate mechanical properties, and a reduced bio-corrosion rate highlights the potential of this surface texturing method, utilizing WEDM, as a promising approach to enhance biodegradable implant materials. © 2025 The Authors. Publishing services by Elsevier B.V. on behalf of KeAi Communications Co. Ltdé This is an open access article under the CC BY license. http://creativecommons.org/licenses/by/4.0/