Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
5 results
Search Results
Item Exploring grinding and burnishing as surface post-treatment options for electron beam additive manufactured Alloy 718(Elsevier B.V., 2020) Karthick Raaj, R.; Vijay Anirudh, P.; Karunakaran, C.; Kannan, C.; Jahagirdar, A.; Joshi, S.; Balan, A.S.S.Numerous additive manufacturing (AM) techniques have been developed over the past decade. Features like immense freedom of intricate part design and shorter lead time make AM routes promising for a wide range of applications spanning aerospace, marine and automobile sectors. Among the various metal AM processes, Electron Beam Additive Manufacturing (EBAM) is being widely explored to realise the potential of Ni-based superalloys and Ti alloys for varied high-performance applications. A novel attempt has been made in this paper to assess the surface integrity of as-built EBAM nickel-based superalloy 718 (AB) subjected to grinding (G), Low Plasticity Burnishing (LPB) and their sequential combination. Apart from their influence on sub-surface microstructures, the effect of process variables during the above post-treatments on the residual stress profiles was also investigated. Results revealed that G + LPB results in about 0.6 ?m lower surface roughness, 17% improved microhardness compared to AB + LPB, and higher compressive surface residual stress as compared to LPB processed EBAM samples. The sequential grinding and LPB - improved microhardness, was also found to extend about 500 ?m more when compared to the LPB process. The G + LPB, which is greatly influenced by the prior grinding, smoothens the surface and thus results in a better surface finish. Highest hardness, superior surface finish, reduced porosity and improved compressive residual stress were observed in samples that adopted the AB + G + LPB sequence over other samples, with the LPB step at 40 MPa yielding the best results. © 2020 Elsevier B.V.Item Effect of cryogenic grinding on fatigue life of additively manufactured maraging steel(MDPI AG, 2021) Balan, A.S.S.; Kannan, C.; Kumar, A.V.; Hariharan, H.; Pimenov, D.Y.; Giasin, K.; Nadolny, K.Additive manufacturing (AM) is replacing conventional manufacturing techniques due to its ability to manufacture complex structures with near?net shape and reduced material wastage. However, the poor surface integrity of the AM parts deteriorates the service life of the components. The AM parts should be subjected to post?processing treatment for improving surface integrity and fatigue life. In this research, maraging steel is printed using direct metal laser sintering (DMLS) process and the influence of grinding on the fatigue life of this additively manufactured material was investigated. For this purpose, the grinding experiments were performed under two different grinding environments such as dry and cryogenic conditions using a cubic boron nitride (CBN) grinding wheel. The results revealed that surface roughness could be reduced by about 87% under cryogenic condition over dry grinding. The fatigue tests carried out on the additive manufactured materials exposed a substantial increase of about 170% in their fatigue life when subjected to cryogenic grinding. © 2021 by the authors. Licensee MDPI, Basel, Switzerland.Item Effect of equiaxed grains and secondary phase particles on mechanical properties and corrosion behaviour of CMT- based wire arc additive manufactured AZ31 Mg alloy(Elsevier Ltd, 2023) Manjhi, S.K.; Sekar, P.; Bontha, S.; Balan, A.S.S.Wire arc additive manufacturing (WAAM) has drawn tremendous attention for manufacturing large and complex components of lightweight material at a moderate cost due to its high deposition rate and energy efficiency. Generally, WAAM-Mg alloy comprises columnar and columnar dendrite grains due to high cooling rates and thermal gradients responsible for anisotropic mechanical properties. To overcome this challenge, in this work, CMT-WAAM, which generally uses comparatively low heat input (33% lower than conventional WAAM), was used to deposit AZ31 Mg thin wall. The metallurgical characterization of the deposited thin wall of the top (T), middle (M) and bottom (B) sections reveals equiaxed grains of average sizes ∼ 58, ∼ 63 and ∼ 38 µm, respectively. In addition, TEM results exhibit the formation of secondary phase particles, i.e., β-Mg17Al12 and ɳ-Al8Mn5. Further, the ultimate tensile strength (UTS) and % elongation (% EL) in the travel direction (UTS = 224 MPa, % EL= 23.47%) are superior to that obtained in the build direction (UTS = 217 MPa, % EL = 20.82%). The corrosion resistance of WAAMed AZ31 Mg alloy is higher than wrought (cold rolled) AZ31 Mg alloy in Hank's balanced salt solution (HBSS). The results of this study reveal the potential of CMT-WAAM to deposit different grades of Mg with desired microstructure, mechanical properties and corrosion resistance. © 2023 CIRPItem Evaluation of functionally graded YSZ - IN625 clad without bond coat using laser directed energy deposition(Elsevier B.V., 2023) Likhwar, J.; Thanumoorthy, R.S.; Bontha, S.; Balan, A.S.S.M-CrAlY or M-Cr-based bond coats are used as a buffer layer to apply ceramic thermal barrier coatings (TBCs) to metal turbine blades. However, due to oxygen diffusion, thermally grown oxides grow over the bond coat material, leading to coating failure in the components. Therefore, this study attempts to fabricate a novel TBC-coated IN625 without bond coat material using a Functional grading approach. The findings from this study may pave the way for processing functionally graded ceramic materials using Laser Additive manufacturing techniques. This study also evaluates the performance of functional grading in joining dissimilar materials using small spot-size laser sources. In the present study, samples were fabricated for three sample conditions: S1: direct clad, S2: 25% linear grading, and S3: 50% linear grading. The interface between Yttria Stabilized Zirconia (YSZ) and IN625 for the S1 sample showed discontinuous and horizontal cracks along the interface due to steep variations in thermal properties. However, the interface of S2 and S3 samples showed good adhesion and a smooth transition in microstructure between IN625 and YSZ as a result of functional grading. SEM micrographs showed homogeneous YSZ distributions without segregation within the IN625 matrix. This was attributed to strong Marangoni flow as a result of the small spot-size laser beam used in this study. © 2023 Elsevier B.V.Item Hybrid additive manufacturing of ER70S6 steel and Inconel 625: A study on microstructure and mechanical properties(Elsevier Ltd, 2023) Rodrigues, J.P.; Thanumoorthy, R.S.; Manjhi, S.K.; Sekar, P.; Arumuga Perumal, D.A.; Bontha, S.; Balan, A.S.S.Hybrid Additive Manufacturing (HAM) is currently being explored because of its potential to achieve trade-off between build capacity and feature resolution. The present study aims at fabricating ER70S6-Inconel 625 (IN625) bimetallic clad using hybrid Wire Arc Additive Manufacturing (WAAM) and Laser Directed Energy Deposition (LDED) processes. Microstructure evaluation was performed at the cross section of bimetallic clad for distinct materials as well as the interface. WAAM built ER70S6 revealed equiaxed ferritic grains, whereas laser deposited IN625 region showed columnar dendrites with under developed secondary arms. However, the first layer of IN625 exhibited columnar dendrite with secondary arms due to the influence of diffused Fe from the base ER70S6 steel under the action of concentrated laser heat source, which was revealed by energy dispersive spectroscopy (EDS) maps. The measured microhardness across the cross section of the deposit showed values corresponding to inherent material system. The interface did not reveal presence of any intermetallic phases which was confirmed by hardness results and X-Ray diffraction. Shear test revealed superior bond strength between the two materials, maintaining average strength of 452 MPa. The fractography images exhibited fine dimples along with cleavages indicating mixed fracture characteristics. This additive manufacturing method explores a new dimension in multi-material fabrication which, when customized for different materials, serve critical areas in the aerospace and defence sector. © 2023 Elsevier Ltd