Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
Search Results
Item Enhancing fatigue performance of AZ31 magnesium alloy components fabricated by cold metal transfer-based wire arc directed energy deposition through LPB(KeAi Communications Co., 2024) Manjhi, S.K.; Bontha, S.; Balan, A.A.S.Cold Metal Transfer-Based Wire Arc Directed Energy Deposition (CMT-WA-DED) presents a promising avenue for the rapid fabrication of components crucial to automotive, shipbuilding, and aerospace industries. However, the susceptibility to fatigue of CMT-WA-DED-produced AZ31 Mg alloy components has impeded their widespread adoption for critical load-bearing applications. In this study, a comprehensive investigation into the fatigue behaviour of WA-DED-fabricated AZ31 Mg alloy has been carried out and compared to commercially available wrought AZ31 alloy. Our findings indicate that the as-deposited parts exhibit a lower fatigue life than wrought Mg alloy, primarily due to poor surface finish, tensile residual stress, porosity, and coarse grain microstructure inherent in the WA-DED process. Low Plasticity Burnishing (LPB) treatment is applied to mitigate these issues, which induce significant plastic deformation on the surface. This treatment resulted in a remarkable improvement of fatigue life by 42%, accompanied by a reduction in surface roughness, grain refinement and enhancement of compressive residual stress levels. Furthermore, during cyclic deformation, WA-DED specimens exhibited higher plasticity and dislocation density compared to both wrought and WA-DED + LPB specimens. A higher fraction of Low Angle Grain Boundaries (LAGBs) in WA-DED specimens contributed to multiple crack initiation sites and convoluted crack paths, ultimately leading to premature failure. In contrast, wrought and WA-DED + LPB specimens displayed a higher percentage of High Angle Grain Boundaries (HAGBs), which hindered dislocation movement and resulted in fewer crack initiation sites and less complex crack paths, thereby extending fatigue life. These findings underscore the effectiveness of LPB as a post-processing technique to enhance the fatigue performance of WA-DED-fabricated AZ31 Mg alloy components. Our study highlights the importance of LPB surface treatment on AZ31 Mg components produced by CMT-WA-DED to remove surface defects, enabling their widespread use in load-bearing applications. © 2024Item Process parameter optimization for laser directed energy deposition (LDED) of Ti6Al4V using single-track experiments with small laser spot size(Elsevier Ltd, 2024) Gonnabattula, A.; Thanumoorthy, R.S.; Bontha, S.; Balan, A.A.S.; Anil Kumar, V.A.; Kanjarla, A.K.Single-track experiments are routinely used in the optimization of process parameters in additive manufacturing processes. Most of the process parameter optimization studies use a laser spot size of 1 mm or more. Since laser spot size affects the input energy density and in turn the efficiency of the deposition process, it is important to develop process maps every time a laser of different spot sizes is used. In this work, we determine the process maps for a laser of 0.6 mm spot size. By combining the process maps and the metallographic inspection, we estimate the optimum process parameters (laser power, scan speed, powder feed rate) for building Ti6Al4V components using powder-based laser-directed energy deposition(LDED). Single-tracks corresponding to 64 different parameter combinations are deposited. After eliminating the process parameter combinations resulting in defective tracks, the optimum process parameters of 300 W laser power and 720 mm min−1 scan speed is established by considering the relationship between the process parameters and the geometrical features of the deposit. The experimental results are then used to calibrate the modeling parameters of a three-dimensional finite element model for simulating the deposition process. © 2024 Elsevier LtdItem Effect of surface remelting on the characteristics of IN718 components fabricated using laser powder directed energy deposition(Institute of Physics, 2024) Thanumoorthy, R.S.; Jadhav, S.V.; Oyyaravelu, R.; Bontha, S.; Balan, A.A.S.Laser Powder Directed Energy Deposition (LP-DED) fabricated components exhibit poor surface finish, necessitating additional post-processing steps prior to their practical application. Enhancing the surface quality of additively manufactured IN718 specimens through conventional post-processing methods is particularly challenging, given the material’s poor machinability and the complexity of the fabricated components. The current study is centered on comprehending the impact of Laser Surface Remelting (LSR) on the surface properties of Laser Powder Directed Energy Deposited (LP-DED) IN718 material. To gain insights into how remelting influences surface characteristics, remelting was carried out using various sets of parameters. The remelted zone exhibited a refined grain structure, leading to increased hardness. Moreover, significant reductions in surface roughness and residual stress were observed in the remelted samples. Regression analysis indicated that laser power played a pivotal role, with positive impact on surface finish and depth of influence but a negative impact on residual stress and hardness. Therefore, considering all the comparison metrics, remelting using laser power of 150 W and a scan speed of 1140 mm min−1 were found to yield optimal surface conditions. © 2024 IOP Publishing Ltd. All rights, including for text and data mining, AI training, and similar technologies, are reserved.