Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
4 results
Search Results
Item An overview of after-treatment systems for diesel engines(Springer Verlag service@springer.de, 2018) Ayodhya, A.S.; Gottekere Narayanappa, K.G.Vehicular pollution has become a major problem in urban areas due to the exponential rise in the number of automobiles. Typical exhaust emissions which include nitrogen oxides (NOx), hydrocarbons (HC), carbon monoxide (CO), soot, and particulate matter (PM) undoubtedly have an unpleasant effect on the environment. Several pollution control bodies are taking this subject seriously and issuing stringent emission norms which are to be complied strictly. Thus, regulation of these harmful pollutants is the need of the hour. Alternative fuels such as biodiesels and alcohols which are considered as a potentially viable solution for the problem of fossil fuel depletion also tend to require exhaust gas after-treatment in order to comply with the upcoming emission norms. Hence, this paper attempts to give a brief insight on the development and advances of different after-treatment devices like diesel particulate filter (DPF), lean NOx trap (LNT), diesel oxidation catalyst (DOC), and selective catalytic reduction (SCR). © 2018, Springer-Verlag GmbH Germany, part of Springer Nature.Item Combined effect of exhaust gas recirculation (EGR) and fuel injection pressure on CRDI engine operating with jatropha curcas biodiesel blends(Taylor's University # 1, Jalan Taylor's Subang Jaya, Selangor Darul Ehsan 47500, 2017) Bedar, P.; Lamani, V.T.; Ayodhya, A.S.; Kumar, G.N.This work investigates the influence of Exhaust gas recirculation (EGR) and injection pressure on the performance and emissions of CRDI engine using Jatropha curcas biodiesel blends of 10% and 20% (B10 and B20). Experiments were carried out for three fuel injection pressures (FIP) of 300, 400 and 500 bar with 15% and 20% EGR rate at constant speed of 2000 rpm and standard injection timing of 150 BTDC. Parameters like brake thermal efficiency and emission characteristics such as smoke opacity, oxides of nitrogen (NOx), hydrocarbon (HC) and carbon mono-oxide (CO) were measured and analysed. The results showed improvement of performance in terms of brake thermal efficiency for blends B10, B20 and with 15%EGR rate. Smoke, HC and CO decreased while slightly increasing NOx emissions when working with biodiesel. In summary, it is optimized that engine running with combination of B20 blend and 15% EGR rate culminates into NOx reductions without affecting engine efficiency and other emissions like smoke opacity, hydrocarbon and carbon mono-oxide. © School of Engineering, Taylor’s University.Item Effect of exhaust gas recirculation on a CRDI engine fueled with waste plastic oil blend(Elsevier Ltd, 2018) Ayodhya, A.S.; Lamani, V.T.; Bedar, P.; Kumar, G.N.The inevitable rise in the usage of plastic poses a serious threat to the environment owing to their non-biodegradable nature. The lack of proper infrastructure for treating and recycling plastic wastes give rise to the disposal problem. However, the oil synthesized from these waste plastics can be used as an alternative fuel for C.I engines which not only helps to tackle the disposal problem but also aids in recovering precious energy from these wastes. This experimental investigation aims to study the effects of plastic-diesel blend(P30) fuel on the performance, emission and combustion characteristics of a twin cylinder CRDI engine operating at different EGR rates (0%, 10% and 20%). The experimental results showed a slight drop in the engine performance while operating with plastic blend, mainly overall due to its higher viscosity and lower heating value. The vast upsurge of NOX emissions with plastic blend was mitigated by the aid of EGR methodology. Marginal increase in the discharge of regulated emissions like HC, CO and soot were noticed for both plastic blend as well as EGR operations. The experiments were carried out for five different loading conditions varying from 0% to 80% in steps of 20% each and found out that waste plastic-diesel blend can be successfully used as an alternative fuel in diesel vehicles without any prior modifications in the engine. © 2018 Elsevier LtdItem NOx reduction studies on a diesel engine operating on waste plastic oil blend using selective catalytic reduction technique(Elsevier B.V., 2019) Ayodhya, A.S.; Lamani, V.T.; Thirumoorthy, M.; Kumar, G.N.The constant escalation in the consumption of petroleum products has compelled researchers to discover for new alternative fuels which can be successfully incorporated in the existing automotive engines. Oil derived from waste plastics is one such alternative, which not only ensures longevity of fossil fuels but also assists in bringing down the hazardous impacts caused by the improper disposal of plastic wastes. This work focuses on the utilization of valuable energy of toxic non-biodegradable waste plastics to lucratively be used as an alternative fuel. An attempt was further made to reduce the NO X emissions which increased with the use of waste plastic oil blend. The main objective of this experimental investigation is to study the performance & emission characteristics of a twin cylinder CRDI engine subjected to selective catalytic reduction (SCR) after-treatment technique. Different flow rates of ammonia as a reducing agent were tested and concluded that a flow rate of 0.5 kg/hr furnishes optimum results. A comparison of NO X reduction efficiency was also made between SCR and EGR techniques. The comparison eventually indicated that SCR gives better NO X conversion efficiency at higher loads without any adverse effect on the engine performance while operating on Waste Plastic Oil blend (P30). © 2018 Energy Institute