Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
3 results
Search Results
Item Semi-analytical method for heat and moisture transfer in packed bed of silica gel(2011) Ramzy K, A.; Ashok Babu, T.P.; Kadoli, R.A semi-analytical model for the heat and mass transfer of adsorption and desorption processes of the vertical solid desiccant packed bed dehumidifier is presented on the basis of quasi-steady state assumption, and is solved using close form integration with the limits equivalent to bed and time increments, and numerically by Runge-Kutta Fehlberg and forward scheme finite difference techniques. The most important parameters during the dehumidifier operation, namely, (i) exit air temperature and humidity, (ii) axial temperature distribution in the bed and (iii) water content are evaluated. Stability of the semi-analytical method is investigated and found that the main parameters affecting the model stability are the bed and time increments size. A dimensionless parameter combining time and bed increments size and air velocity named velocity ratio is defined and investigated. It is found that when the velocity ratio equals the ratio of particle diameter to bed length, the method is stable, and as the velocity ratio is made smaller beyond the stable velocity ratio, the results remain unchanged. The results of semi-analytical and numerical models agree well with the experimental results for both desorption and adsorption processes. Using the proposed semi-analytical model, the minimum and maximum relative errors for exit air temperature are 2.24% and 11.78%, respectively and for exit air humidity the minimum and maximum errors are 3.79% and 27.17% respectively. © 2010 Published by Elsevier Ltd. All rights reserved.Item Performance studies on the desiccant packed bed with varying particle size distribution along the bed(2012) Ramzy K, A.; Kadoli, R.; Ashok Babu, T.P.The transient heat and mass transfer in a desiccant packed bed containing varying particle diameter distribution along the axial direction has been investigated using the pseudo gas controlled approach that considers the heat conduction in the bed. The numerical results of the present model and the experimental data from literature show good agreement with a maximum root of mean square of errors of 3% and 2% for exit air temperature and humidity ratio, respectively. The improvement in the total mass adsorbed and/or reduction in pressure drop has been investigated for various cases of packed bed namely, uniform particle diameter, linear, parabolic and cubic ascending and descending distributions. It has been found that there is a 25.7% reduction in pressure drop with negligible reduction in the total mass adsorbed for a desiccant bed with cubic type particle size distribution when compared to the bed with uniform particle diameter of 1.0 mm. A threshold flow velocity exists below which the total mass adsorbed is independent of particle diameter distribution type. © 2012 Elsevier Ltd and IIR. All rights reserved.Item Significance of axial heat conduction in non-isothermal adsorption process in a desiccant packed bed(2014) Ramzy, K.A.; Kadoli, R.; Ashok Babu, T.P.Numerical simulation of heat and moisture interactions between air stream and the particles in a desiccant bed provide useful insight on the dynamics of the bed and performance characteristics. Current study introduces a mathematical model for the heat and moisture transfer in desiccant packed bed based on solid side resistance (SSR) model that will now consider heat conduction along the bed. Adsorption and desorption experimental tests have been carried out for validating both solid side resistance (SSR) and solid side resistance with axial heat conduction (SSR-AC) models. The models have been used to investigate the influence of various design parameters like air velocity, particle diameter, bed length and the number of units of mass transfer, on the significance of axial heat conduction. It has been found that increasing the particle diameter or increasing air flow velocity or decreasing the bed length will reduce the influence of axial heat conduction in the bed. Moreover, it has been found that the difference in the bed performance evaluated due to the absence of axial heat conduction in the bed is notably decreasing with the decrease in the number of transfer units of heat or mass. From this study, it is recommended to consider the axial heat conduction term when number of transfer units of mass and heat are greater than unity. © 2013 Elsevier Masson SAS. All rights reserved.