Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item Computation of fluid flow in double sided cross-shaped lid-driven cavities using Lattice Boltzmann method(Elsevier Ltd, 2018) Bhopalam, S.B.; Arumuga Perumal, D.A.; Yadav, A.K.This work implements Lattice Boltzmann method to compute flows in double-sided cross-shaped lid-driven cavities. Firstly, a complicated geometry which is a symmetrized version of the staggered lid-driven cavity namely, the double-sided cross-shaped lid-driven cavity with antiparallel uniform wall motion is studied employing Single as well as Two Relaxation time models. The streamline patterns and vorticity contours obtained for low to moderate Reynolds numbers (150–1000) are compared with published results and found to be in good accordance. Next, this code is extended to simulate flows in a double-sided cross-shaped lid-driven cavity with parallel uniform wall motion. The effect of three dimensionality is also studied for low Reynolds numbers. Lattice Boltzmann method is then used to investigate the oscillating double-sided cross-shaped lid-driven cavity with antiparallel and parallel wall motions. The movement and formation of primary and secondary vortices have been well captured with the variation of Reynolds numbers and oscillating frequencies for uniform and oscillating wall motions. Reasonable agreements with the established results have been observed for the double-sided cross-shaped cavity with uniform wall motions, while new results have been obtained in the case of oscillating wall motions. © 2018 Elsevier Masson SASItem Fluid flow characteristics in double-sided lid-driven microcavity using lattice boltzmann method(Begell House Inc. orders@begellhouse.com, 2019) Rajan, I.; Arumuga Perumal, D.A.; Yadav, A.K.In this study, we analyze the fluid flow characteristic of rarefied gas flows in double-sided lid-driven microcavity subjected to various combinations of boundary conditions that simulate the slip at the walls using lattice Boltzmann method (LBM) constituting a single relaxation time (SRT) model. The fluid motion inside a closed square container with two rigid walls and two moving walls constitutes an exemplar for internal vortex flows. First, a complicated geometry, namely, the single-sided lid-driven microcavity is studied using the LBM-SRT model. Next, this code is extended to simulate flows in a double-sided microcavity flow. Numerical computation of fluid flow incorporating various slip boundary conditions as bounce-back and specular boundary condition (BSBC) for different values of tangential accommodation momentum coefficient (TMAC) has been investigated. Various values of Knudsen number in the slip and transition regime (Kn = 0.01, 0.05, 0.10, 0.135, and 0.15) along with different aspect ratios of 0.33, 0.50, 1.0, 2.0, and 3.0 have been considered in this study. The streamline patterns and velocity profiles were obtained for different Knudsen numbers. The formation and movement of primary vortices have been well captured with the variation of Knudsen numbers for different aspect ratios of microcavity. © 2019 by Begell House, Inc.Item Study of adiabatic obstacles on natural convection in a square cavity using lattice boltzmann method(American Society of Mechanical Engineers (ASME) infocentral@asme.org, 2019) Karki, P.; Yadav, A.K.; Arumuga Perumal, D.A.This study involves the effect of adiabatic obstacles on twodimensional natural convection in a square enclosure using lattice Boltzmann method (LBM). The enclosure embodies squareshaped adiabatic obstacles with one, two, and four in number. The single obstacle in cavity is centrally placed, whereas for other two configurations, a different arrangement has been made such that the core fluid zone is not hampered. The four boundaries of the cavity considered here consist of two adiabatic horizontal walls and two differentially heated vertical walls. The current study covers the range of Rayleigh number (10 3 ? Ra ? 10 6 ) and a fixed Prandtl number of 0.71 for all cases. The effect of size of obstacle is studied in detail for single obstacle. It is found that the average heat transfer along the hot wall increases with the increase in size of obstacle until it reaches an optimum value and then with further increase in size, the heat transfer rate deteriorates. Study is carried out to delineate the comparison between the presences of obstacle in and out of the conduction dominant zone in the cavity. The number of obstacles (two and four) outside of this core zone shows that heat transfer decreases despite the obstacle being adiabatic in nature. © 2019 by ASME.Item Comparative studies on air, water and nanofluids based Rayleigh–Benard natural convection using lattice Boltzmann method: CFD and exergy analysis(Springer Science and Business Media B.V., 2022) Karki, P.; Arumuga Perumal, D.A.; Yadav, A.K.The present study incorporates laminar natural convection and entropy generation in Rayleigh–Benard (R–B) convection with air, water and alumina–water nanofluid as working fluids. The fluid flow and energy equations are solved using D2Q9 and D2Q5 LBM models, respectively. The effects of Rayleigh numbers (Ra = 5 × 103, 104, 105) and volume fractions (? = 0 to 0.08) of nanoparticles on heat transfer and irreversibility are investigated. Results show that the heat transfer evaluated based on Nusselt number is enhanced due to addition of nanoparticles in the base fluid. The maximum enhancement in Nusselt number is found to be 13.93% at Ra = 105 with 8% of nanoparticle in base fluid. The various irreversibilities considered in this study are thermal, fluid flow and total irreversibility, where fluid flow and total irreversibilities in the study depend on irreversibility ratio. The irreversibility ratios taken into account are 10–2, 10–3, 10–4 and 10–5. One facet of study shows the deviation in onset of critical Rayleigh number for air is 1.58%. The other facet indicates dimensionless heat transfer, fluid flow and total irreversibility decrease with the increase in volume fraction of nanoparticles in the base fluid. The analyzed results of irreversibilities are presented in normalized form. In addition, dimensionless entropy generation maps and Bejan number contours are also plotted. © 2021, Akadémiai Kiadó, Budapest, Hungary.Item Simulation of fluid flow in a lid-driven cavity with different wave lengths corrugated walls using Lattice Boltzmann method(Taiwan Institute of Chemical Engineers, 2023) Fatima, N.; Rajan, I.; Arumuga Perumal, D.A.; Anbalagan, A.; Ahmed, S.A.A.; Gorji, M.R.; Ahmad, Z.Background: The Lid-driven cavity (LDC) flow is an interesting problem in fluid mechanics. The lattice Boltzmann Method (LBM) is used to simulate fluid flow in a LDC with different wave lengths corrugated walls. Methods: The D2Q9 model is used for the 2D bounded domain where the analysis of bottom-bounded wall corrugations on the flow features is analyzed. For validation, a square corrugation along the bottom wall with a driven top wall is considered. A lattice size independence study is performed and the LBM code is substantiated with published results for different values of Reynolds number. The code is then modified by using sinusoidal corrugated walls with different wavelengths along the bottom surface. Significant finding: The streamline patterns, vorticity contours and kinetic energy contours are studied for different Reynolds number. Results shown that the position, number and size of vortices depend on the number of corrugations and value of Reynolds number used. The secondary vortices tend to increase in size as the Reynolds number increase. The kinetic energy contours show maximum energy near the top wall which reduces inside the cavity. © 2023Item Three-dimensional simulations of fluid flows in oscillating lid-driven cavities using lattice Boltzmann method(Institute of Physics, 2023) Bhopalam, S.R.; Arumuga Perumal, D.A.; Yadav, A.K.We utilize the lattice Boltzmann method to conduct three-dimensional simulations of incompressible flows in oscillating cubic lid-driven cavities. Our investigation focuses on examining the impact of Reynolds number and oscillating frequency on the flow field. Notably, we observe that the flow field can be adequately approximated as two-dimensional within the low and intermediate Reynolds number range, but this approximation is no longer valid for high Reynolds numbers. Additionally, we find that high Reynolds numbers correspond to transient flow fields, while low and moderate Reynolds numbers exhibit quasi-steady periodic flow fields. Our study holds significant relevance for industrial processing applications, where the Reynolds numbers and oscillating frequencies can be optimized to achieve a desired flow field. © 2023 The Japan Society of Fluid Mechanics and IOP Publishing Ltd.