Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
4 results
Search Results
Item Development and characteristics of accumulative roll bonded Mg-Zn/Ce/Al hybrid composite(Elsevier Ltd, 2017) Anne, G.; Ramesh, M.R.; Shivananda Nayaka, H.; Arya, S.B.; Sahu, S.Accumulative roll bonding (ARB) process have been used develop Mg-2%Zn/Ce/Al hybrid composite and microstructure, mechanical and corrosion properties were investigated. The electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) revealed that the grains are significantly reduced and reaches up to 1 ?m in Mg-2%Zn layer and 1.8 ?m in Al layer having high angle misorientation of grain boundaries after subjected to 5-passes of the ARB process. The Al17Mg12, AlMg4Zn11 and Al11Ce3 intermetallic phases were observed through the XRD analysis. Mechanical properties of the hybrid composite improved with increase in the number of ARB passes which is attributed to work hardening, grain refinement and uniform distribution of Ce particles. Presence of Ce in the hybrid composite restricts the phenomenon of dynamic recrystallization and prevents the grain growth during ARB process. The corrosion rate of Mg-Zn/Ce/Al hybrid composite (0.72 mm/y) improved about 3.3 times as compared to that of Mg-2%Zn alloy (2.37 mm/y). © 2017 Elsevier B.V.Item Impact of ply stacking sequence on the mechanical response of hybrid Jute-Banana fiber phenoplast composites(Institute of Physics, 2024) Maruthi Prashanth, B.H.; Ramesh, S.; Shivakumar Gouda, P.S.S.; Naik, G.M.; Sharma, P.; Jagadeesh, C.; Mahantesh, M.M.; Anne, G.Natural fiber composites are increasingly gaining popularity as a cost-effective and environmentally friendly alternative to synthetic fibers. Incorporating a variety of fibers enhances mechanical properties. The arrangement of fibers plays a crucial role in determining the mechanical characteristics of laminate composites. Therefore, the primary objective of this study is to investigate how the stacking order of jute (J) and banana (B) fibers affects the mechanical behaviour of composites made from phenolic resins. Four different fiber mat stacking sequences (J/B/B/J, B/J/J/B, J/B/J/B, and J/J/B/B) were used for developing the eco-fiber composites using the heat-press technique. Several mechanical parameters were assessed, including tensile strength, flexural strength, impact strength, and inter-laminar shear strength (ILSS). The experimental results indicated that the JBBJ composite exhibits superior tensile strength (46.65 MPa) and modulus (993 MPa) compared to the other composites due to the presence of high-strength jute fibers on the surface. Additionally, the flexural strength of the JBBJ composite (87.24 MPa) was found to be noteworthy. It was observed that the impact strength of jute fibers surpasses that of banana fibers. Consequently, the JBBJ composite demonstrates higher values for energy absorption (0.482 J) and impact strength (120 J m−1) compared to the other composites tested. Moreover, the JBBJ composite displays higher inter-laminar shear strength and hardness values compared to BJJB, JBJB, and JJBB by 30%, 35%, and 43%, respectively. Scanning electron microscope microphotographs reveal strong correlational fracture failure mechanisms, indicative of improved mechanical properties in the JBBJ composite. Based on the experimental results, it is evident that the JBBJ composite can be utilized in lightweight applications. © 2024 The Author(s). Published by IOP Publishing Ltd.Item Effect of addition of Ce and accumulative roll bonding on structure-property of the Mg-Ce-Al hybrid composite and its prediction and comparison using artificial neural network (ANN) approach(Institute of Physics, 2024) Anne, G.; Bhat, N.; Vishwanatha, H.M.; Ramesh, S.; Maruthi Prashanth, B.H.; Sharma, P.; Aditya Kudva, S.; Jagadeesh, C.; Nanjappa, Y.Light alloys play a crucial role in realizing the national strategy for energy conservation and emission reduction, as well as promoting the upgrading of manufacturing industries. Mg/Al composite laminates combine the corrosion resistance and ductility of aluminium alloy with the lightweight characteristics of magnesium alloy. The addition of Ce (rare earth elements) can improve the mechanical properties of magnesium via grain refinement and improve the ductility of the hybrid composites. In the present work, an investigation on addition of Ce into the Mg/Al matrix through Accumulative Roll Bonding (ARB) has been presented. The Mg/Ce/Al hybrid composite consists of Mg-4%Zn alloy and Al 1100 alloy with 0.2% Ce particles added between the dissimilar layers. The changes occurred in the evaluation of microstructure, corrosion and mechanical properties of the Mg/Ce/Al hybrid composite as a result of deformation process and also the addition of Ce have been explicated. The ARB parameters: temperature, rolling speed, percentage reduction, and aging time, have been studied. An increase of about 2.36 times in strength and hardness of the hybrid composite, has been reported. Further, the structure-property relations in the Mg/Ce/Al hybrid composites were aslo predict and compare using machine learning models: Decision Tree and Multi-Layer Perceptron (MLP) models. © 2024 The Author(s). Published by IOP Publishing Ltd.Item Synthesis and characteristics of Fe/Ni/Cr oxide nanoparticles/PLA hybrid composite coatings on Mg–Zn–Ca alloy(Elsevier Editora Ltda, 2025) Kumar, P.; Kudva S, A.; T, A.; S, R.; Ramesh, M.R.; Prabhu, A.; Anne, G.Biodegradable materials research is dominated by magnesium and alloys thereof due to their excellent compatibility with biological barriers and biomechanical strength. Despite this, the rapid degradation of these materials in the physiological environment is the primary obstacle hindering their utilization in biomedical applications. This issue must be resolved before considering their use in clinical applications. To improve resistance towards corrosion and enhance biological efficacy and compatibility, the surfaces were coated with polylactic acid (PLA) using dip-coating. In this study, iron (Fe), nickel (Ni), and chromium (Cr) oxide nanoparticles from the Coleus amboinicus extract are synthesized and mixed with PLA to develop hybrid composite coatings, which are then applied onto the Mg–4Zn–1Ca alloy. Coleus amboinicus is known for its various medicinal properties, including immunoregulatory effects, antimicrobial activity, anti-inflammatory properties, and potential use in treating sepsis and other ailments. The extracted FeNiCr was used the develop composite coatings on Mg–4Zn–1Ca alloy. The coating improves biocompatibility, antibacterial properties, and overall performance of biomedical implants. These composite coatings were evaluated for their morphological and optical characteristics using a scanning electron microscope (SEM), 3-D non-contact profilometer, Fourier transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD). The corrosion characteristics of developed samples were measured by electrochemical corrosion in standard simulation body fluid (SBF) at 37 °C. Furthermore, cytocompatibility of the PLA hybrid composites on osteoblast cells and apoptosis detection using acridine orange-ethidium bromide. Our developed coating showed ratings of 5B and 4B were obtained for FeNiCr/PLA NC- ball burnished (BB) Mg and FeNiCr/PLA nano composite (NC)–Mg samples, respectively, demonstrating the exceptional coating strength and the substrate. The corrosion rate of the FeNiCr/PLA NC-BB-Mg sample (0.02890 mm/y) is two-fold times increased against comparison with the H Mg sample (0.00012 mm/y). Cytocompatibility indicates their cytocompatibility for bone implant applications. © 2025 The Authors