Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
18 results
Search Results
Item Thermal degradation and swelling of thermoplastic vulcanizates from NBR/SAN and NBR/Scrap computer plastics blends(Huthig GmbH, 2009) Anandhan, S.; Rajeev, R.S.; De, S.K.; Bhowmick, A.K.Thermoplastic elastomeric blends of nitrile rubber (NBR)/poly(styrene- coacrylonitrile) (SAN) and NBR/scrap computer plastics (SCP) based on acrylonitrile-butadiene-styrene terpolymer (ABS) were prepared. Thermoplastic elastomeric blends of NBR/SAN containing various amounts of a model waste nitrile rubber powder (w-NBR) were also prepared. Thermogravimetric analysis of the above blends was performed in a nitrogen atmosphere. Both Friedman and Flynn-Wall-Ozawa methods were used for the evaluation of activation energies of thermal degradation of these blends. The dynamically vulcanised blends exhibit higher amount of activation energies for thermal degradation than the unvulcanised ones. Swelling studies were performed in various solvents having different solubility parameter values and maximum swelling was found to occur in a solvent having a solubility parameter that was closer to that of the blend components, i.e., around 20MPa1/2. Dynamically vulcan-ised blends show excellent resistance to IRM #903 oil as well as four chosen solvents possessing different solubility parameters (E).Item Solution electrospinning of styrene-acrylonitrile random copolymer from dimethyl sulfoxide(Springer India sanjiv.goswami@springer.co.in, 2013) Senthil, T.; Anandhan, S.Electrospinning is an efficient and versatile technique for the fabrication of ultrafine fibers having diameters ranging from nano to sub-micron level for various potential applications. In this study, we have investigated the influence of process and solution parameters, such as solution concentration, flow rate and applied voltage, on the morphology of electrospun poly(styrene-co-acrylonitrile) (SAN) fibers. Morphology and average diameter (Davg.) of the electrospun SAN fibers were characterized by scanning electron microscopy (SEM). The SEM results reveal that concentration, applied voltage and flow rate of solution are strongly associated with formation of defects, such as beads, in the fibers. Ultrafine SAN fibers with Davg. in the range of 96-872 nm were obtained by controlling the experimental parameters. The Davg. of electrospun fibers increased with increasing solution concentration, applied voltage and flow rate. Also, the Davg. exhibits a power law relationship with the solution concentration. © 2013 Central Institute of Plastics Engineering & Technology.Item Chemical-resistant Ultrafine Poly(styrene-co-acrylonitrile) Fibers by Electrospinning: Process Optimization by Design of Experiment(2013) Senthil, T.; George, G.; Anandhan, S.The effects of solution and processing parameters on the morphology and diameter of electrospun poly(styrene-co-acrylonitrile) fibers were investigated by design of experiment. Morphology of the electrospun fiber mats were investigated by scanning electron microscopy. With increasing solution concentration, fiber morphology changed from that of a spindle-like beaded one to smooth, and the average fiber diameter increased from 96 to 876 nm. Average fiber diameter gradually increased with applied voltage; however, fiber morphology was only slightly influenced by flow rate. Regression analysis results reveal that solution concentration has the most significant impact on the average and standard deviation of fiber diameter. © 2013 Copyright Taylor and Francis Group, LLC.Item Thermoplastic vulcanizates from post consumer computer plastics/nitrile rubber blends by dynamic vulcanization(Springer Japan, 2013) Anandhan, S.; Bhowmick, A.K.Due to depletion of natural resources and increasing greenhouse emissions, new technologies for the transformation of waste polymers into valuable materials represent one of our greatest current needs. Acrylonitrile-butadiene-styrene terpolymer (ABS) is one of the most widely used engineering plastics and is used as outer casing for electronic equipment. Nitrile rubber (NBR) is used in many applications that demand oil resistance. In an attempt to explore whether these materials can be successfully recycled, we prepared blends of scrap computer plastics (SCP) based on ABS with NBR and waste NBR powder (w-NBR), and investigated their mechanical properties and recyclability. Specifically, we assessed the effect of dynamic vulcanization and replacement of virgin NBR with w-NBR on the properties of 60/40, 70/30, and 80/20 NBR/SCP blends. These blends exhibited thermoplastic elastomeric behavior. The thermoplastic elastomeric blends showed excellent swelling resistance to standard lubricant oil (namely, IRM 903 oil). © 2013 Springer Japan.Item Glass fiber-supported NiO nanofiber webs for reduction of CO and hydrocarbon emissions from diesel engine exhaust(Cambridge University Press, 2014) George, G.; Anandhan, S.In this study, nickel acetate tetrahydrate (NACTH)/poly(styrene-co-acrylonitrile) (SAN) sol was used for the fabrication of nanocrystalline NiO nanofibers. An indigenous setup was developed to use these nanofibers for the oxidation of carbon monoxide (CO) and unburnt hydrocarbons (HC) from diesel engine exhaust. The morphological, compositional, and crystalline properties of the NiO nanofibers obtained after calcination were studied by scanning electron microscopy, Fourier transform infrared (FTIR) spectroscopy, and x-ray diffraction (XRD). Clear evidence of defects in the fibers was observed in ultraviolet-visible-near infrared (UV-Vis-NIR) spectra, Raman spectra, and magnetic property measurements. The NiO nanofiber mats supported by glass fiber mats were efficient in oxidizing CO and HC from diesel engine exhaust, and the maximum efficiency was achieved by using NiO nanofibers with the maximum amount of defects. © © Materials Research Society 2014.Item Glass fiber-supported NiO nanofiber webs for reduction of CO and hydrocarbon emissions from diesel engine exhaust(Cambridge University Press, 2014) George, G.; Anandhan, S.In this study, nickel acetate tetrahydrate (NACTH)/poly(styrene-co-acrylonitrile) (SAN) sol was used for the fabrication of nanocrystalline NiO nanofibers. An indigenous setup was developed to use these nanofibers for the oxidation of carbon monoxide (CO) and unburnt hydrocarbons (HC) from diesel engine exhaust. The morphological, compositional, and crystalline properties of the NiO nanofibers obtained after calcination were studied by scanning electron microscopy, Fourier transform infrared (FTIR) spectroscopy, and x-ray diffraction (XRD). Clear evidence of defects in the fibers was observed in ultraviolet-visible-near infrared (UV-Vis-NIR) spectra, Raman spectra, and magnetic property measurements. The NiO nanofiber mats supported by glass fiber mats were efficient in oxidizing CO and HC from diesel engine exhaust, and the maximum efficiency was achieved by using NiO nanofibers with the maximum amount of defects. © © Materials Research Society 2014.Item Structure-property relationship of sol-gel electrospun ZnO nanofibers developed for ammonia gas sensing(Academic Press Inc. apjcs@harcourt.com, 2014) Senthil, T.; Anandhan, S.Zinc oxide (ZnO) based nanomaterials have been used in various gas sensors due to the wide band gap (3.37. eV), large exciton binding energy and high mobility of charge carriers of ZnO. In this work, nanocrystalline ZnO nanofiber mats were synthesized through combined sol-gel electrospinning techniques followed by calcination, in which poly(styrene- co-acrylonitrile) and zinc acetate were used as the binder and precursor, respectively. Average diameter of the ZnO nanofibers decreased from 400 to 60. nm, while their grain size and crystallinity were enhanced by increasing the calcination temperature. Morphology and structure of the ZnO nanofiber mats were characterized by high resolution transmission electron microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy and X-ray diffraction. ZnO nanofiber mats were found to be superhydrophilic (contact angle was close to 0°) by contact angle measurements. The sensitivity of these ZnO nanofibers in detecting gaseous ammonia was tested using an indigenous set up. Due to their high surface area and superhydrophility, these ZnO nanofiber mats were highly sensitive in sensing gaseous ammonia and the sensitivity of these mats increased as a function of their calcination temperatures. © 2014 Elsevier Inc.Item Comparison of structural, spectral and magnetic properties of NiO nanofibers obtained by sol-gel electrospinning from two different polymeric binders(Elsevier Ltd, 2015) George, G.; Anandhan, S.NiO is a p-type semiconductor with wide band gap energy. In this study, nickel oxide nanofibers were fabricated by sol-gel electrospinning followed by high temperature calcination, using two sacrificial polymeric binders. Poly(2-ethyl-2-oxazoline) (PEtOx) in water and styrene-acrylonitrile random copolymer (SAN) in N,N- dimethylformamide (DMF) along with nickel (II) acetate tetrahydrate (NATH), as metal oxide precursor, were the two distinct polymeric systems used in this study. The morphological and structural properties of NiO fibers obtained from the aforementioned systems were compared with each other. The degradation behavior of the sacrificial polymeric binder imparted a significant effect on the properties of the obtained NiO fibers. The grain sizes and the activation energies for grain growth of NiO fibers from two systems were different. The non-stoichiometric NiO fibers obtained from the SAN/NATH system had a better ferromagnetic behavior as compared with that produced from the PEtOx/NATH system. This non-stoichiometry made a difference also in the optical band gap energies of the NiO nanofibers. © 2015 Elsevier Ltd.Item Morphological and structural characterisation of sol-gel electrospun Co3O4 nanofibres and their electro-catalytic behaviour(Royal Society of Chemistry, 2015) George, G.; Elias, L.; Hegde, A.C.; Anandhan, S.Evolution of hydrogen and oxygen are a crucial part of many renewable energy systems. The replacement of the essential and expensive components in such systems can reduce the capital cost and improve the effectiveness of those systems. In this study, Co3O4 nanofibres were fabricated from sol-gel assisted electrospun poly(styrene-co-acrylonitrile)/cobalt acetate tetrahydrate precursor composite fibres. The morphological and compositional features of the Co3O4 nanofibres obtained after calcination of the precursor nanofibers were studied using scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. The results of X-ray diffraction study and Raman spectroscopy revealed that the average grain size of the fibres increased with the calcination temperature. Clear evidence of defects in the fibres was observed in ultraviolet-visible-near infrared and energy dispersive spectroscopic measurements. The electrocatalytic behaviour of Co3O4 nanofibres obtained at different calcination temperatures was studied using them for the water splitting reaction in an alkaline medium. The maximum efficiency in the hydrogen evolution reaction was achieved using the Co3O4 nanofibres obtained at the lowest calcination temperature, which had the highest surface area and the smallest grain size. © The Royal Society of Chemistry 2015.Item Electrospinning of non-woven poly(styrene-co-acrylonitrile) nanofibrous webs for corrosive chemical filtration: Process evaluation and optimization by Taguchi and multiple regression analyses(Elsevier, 2015) Senthil, T.; Anandhan, S.Nano-fibrous ultra-filtration membranes of poly(styrene- co-acrylonitrile) were produced from n-butanone solution by electrospinning. Effects of governing parameters on morphology and variation in diameter of the electrospun fibers were experimentally investigated by orthogonal experimental design. The process parameters were selected by Taguchi's method. Multiple regression analysis was used to obtain a quantitative relationship between selected electrospinning parameters and average fiber diameter and ANOVA was used to identify the statistically significant parameters and set the optimal level for each parameter. Confirmation experiment revealed a good agreement between the predicted values of the response obtained from optimum level parameters and the observed experimental values. © 2014 Elsevier B.V.