Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
6 results
Search Results
Item Use of nano-ATH as a multi-functional additive for poly(ethylene-co-vinyl acetate-co-carbon monoxide)(Springer Verlag service@springer.de, 2014) George, G.; Mahendran, A.; Anandhan, S.Flame retardant aluminum hydroxide (ATH) nanoparticles of size ?10-20 nm were dispersed in ethylene-vinyl acetate-carbon monoxide terpolymer (EVACO) via solution casting. The effect of filler loading on the crystallizability, thermal, mechanical, flammability, optical and electrical properties of EVACO was evaluated. At 1 % filler loading nano-ATH particles exhibited very good dispersibility in the EVACO matrix and the % crystallinity of EVACO is the highest at this filler loading. The changes in crystallinity were studied by X-ray diffractometry and differential scanning calorimetry. The highest tensile strength was observed for the composite with 1 % nano-ATH loading, which has the best filler dispersion, and the decay in the tensile properties at higher filler loading is due to agglomerations of ATH nanoparticles and polymer-filler interface debonding. The UV absorption of these composites is augmented irrespective of the nano-ATH loading and ATH emerges as a good absorber of UV light. The DC electrical conductivity study of the composites proves that the addition nano-ATH is an efficient way to improve the dielectric properties of EVACO. The presence of nano-ATH improves the flame retardance of these composites. © 2014 Springer-Verlag Berlin Heidelberg.Item Sliding wear and mechanical properties of alumina/glass fabric/epoxy composites(Huthig GmbH, 2015) Shivamurty, B.; Anandhan, S.; Bhat, K.U.In this study, laminates of neat glass fabric/ epoxy composite (GEC) and three levels of Al2O3 filled glass fabric/epoxy composites, designated as 3AGEC, 6AGEC and 9AGEC (micro particulates of Al2O3 - by 3, 6 and 9 wt. % of resin respectively) were prepared using hand lay-up method. 3AGEC exhibits higher tensile strength, flexural strength and flexural modulus besides improved hardness compared to GEC, 6AGEC and 9AGEC. 3AGEC exhibits the lowest specific wear rate compared to GEC, 6AGEC and 9AGEC at all the three loads (i.e., 15, 30 and 45 N) and at a constant sliding velocity of 3.5 m· s-1 for a sliding distance of 1.5 km. It was found that beyond filler content of 3 wt. % is deteriorates the mechanical and sliding wear properties of the composites due to agglomeration of the filler. Also, it was found that lowest factor signifies lowest specific wear rate in both neat and all the Al2O3 filled composites.Item Nanostructured Fly Ash as Reinforcement in a Plastomer-Based Composite: A New Strategy in Value Addition to Thermal Power Station Fly Ash(Springer Netherlands, 2016) Patil, A.G.; Mahendran, A.; Anandhan, S.Class-F fly ash (FA) from a coal-fired thermal power station was subjected to high energy ball milling-induced mechanochemical activation aided by a surfactant. Subsequently, ethylene-octene copolymer/mechanochemically activated FA (EOC/MCA-FA) composites were prepared by solution casting. The surface modification of FA was confirmed from contact angle measurements and FTIR spectroscopy, which accounts for a good interaction between MCA-FA and the polymer matrix. X-ray diffraction reveals that the crystallite size of quartz phase present in FA got reduced, while the relative lattice strain on it increased during milling. Morphological studies revealed that interfacial adhesion between the polymer and MCA-FA is good and this accounts for the improvement in mechanical properties of the composites even at the minimum filler loading. Flame retardance of the matrix polymer is improved by the addition of either fresh FA or MCA-FA. The results imply that FA is a valuable reinforcing filler for ethylene-octene copolymer and its mechanochemical activation is an effective strategy for its future use. © 2014, Springer Science+Business Media Dordrecht.Item Structure-property relationship of halloysite nanotubes/ethylene-vinyl acetate-carbon monoxide terpolymer nanocomposites(SAGE Publications Ltd info@sagepub.co.uk, 2017) George, G.; SelvaKumar, M.; Mahendran, A.; Anandhan, S.Poly(ethylene-co-vinyl acetate-co-carbon monoxide) (EVACO)/halloysite nanotube (HNT) nanocomposite films were solution cast. Dispersion of HNTs in the matrix was analyzed by elemental mapping and the role of HNTs on crystallizability, flammability and thermal, mechanical, and electrical properties of the polymer was evaluated. The nature of interaction between the EVACO matrix and HNTs was studied using Fourier transform infrared spectroscopy. The highest tensile strength was observed for the composite with 1% filler loading, whereas the highest crystallinity was observed for that with 3% filler loading. The decay in the tensile properties at higher filler loading was due to agglomeration of HNTs and debonding of polymer-filler interface. The electrical volume resistivity of the composites decreased with HNT loading because of the ionic charge transfer. The direct current electrical resistivity study of the composites proves that the addition of HNT can improve the antistatic properties of the polymer. © The Author(s) 2015.Item Chitosan composites reinforced with nanostructured waste fly ash(Springer Japan, 2017) Patil, A.G.; Poornachandra, S.; Gumageri, R.; Rajkumar, K.; Anandhan, S.This paper outlines the preparation and characterization of chitosan (CS) composites reinforced with mechano-chemically activated fly ash (MCA-FA). A series of composite films was prepared by solution casting method with varying filler content. Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD) analyses showed good compatibility between the CS matrix and MCA-FA. The surface roughness and irregularity in shape of MCA-FA resulted in its efficient mechanical interlocking with the polymer matrix. This, in turn enhanced the mechanical properties of these composites. All the composite films exhibited a higher tensile strength and a lower percentage of elongation-at-break compared with the pure CS film. The highest tensile strength was observed for the composite films with 1 wt% of filler loading and the reduction in the tensile properties at higher filler loading was due to agglomeration of filler and polymer–filler interface debonding. The tensile strength data were analyzed using Nielsen and Pukanzsky models to understand the interface formation and polymer–filler interactions. Thermal properties showed a marginal improvement due to the incorporation of MCA-FA. Overall, this study indicates that MCA-FA could be used as value added filler in polymer matrix composites. © 2016, Springer Japan.Item Influence of multiwalled carbon nanotubes on the structure and properties of poly(ethylene-co-vinyl acetate-co-carbon monoxide) nanocomposites(John Wiley and Sons Inc, 2021) George, G.; Mahendran, A.R.; SelvaKumar, S.; Anandhan, S.In this work, composites of poly(ethylene-co-vinyl acetate-co-carbon monoxide) (EVACO)/surface-modified multiwalled carbon nanotubes (m-MWCNTs) were prepared using a solution casting technique. Acid treatment was employed for the surface modification of MWCNTs to improve the compatibility between polar EVACO and MWCNTs. The influences of m-MWCNTs on the crystalline, mechanical, thermal, and electrical properties of EVACO at very low filler loading were systematically evaluated. The presence of m-MWCNTs in the EVACO matrix influenced the crystallinity, and the respective changes were determined and quantified using dynamic scanning calorimetry and X-ray diffraction. The mechanical properties of the composites were improved remarkably by the addition of a minute quantity (0.05, 0.1, 0.15, 0.2, and 0.25 wt%) of m-MWCNTs. Additionally, m-MWCNTs in the EVACO matrix improved the thermal stability and electrical properties of EVACO. However, the filler loading is below the threshold loading of the fillers, and there was no drastic improvement in the electrical conductivity of the composite. © 2021 Society of Plastics Engineers.