Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
4 results
Search Results
Item Effect of Mechanical Alloying on the Microstructure of CoCrNiTiMo x High Entropy Alloy(Springer, 2022) Addepalli, S.N.; Joladarashi, S.; Ramesh, M.R.; Arya, S.B.The present research focuses on synthesizing nanocrystalline CoCrNiTiMox (x: molar ratio; x = 1, 1.5 at.%, respectively) high entropy alloy by mechanical alloying of pure metal powders for further application as feedstock in the atmospheric plasma spray process. The paper describes the phase evolution and microstructural transformation of milled powders with respect to the ball milling time and speed. A Retsch PM 100 ball mill with a ball to powder ratio of 10:1 and speeds of 200 and 300 rpm are used to synthesize the feedstock powder for plasma spraying. The ball milled powders were assessed for particle size, phase transformation and surface morphologies at regular intervals of 10, 20, 30, 40 and 50 h to optimize the ball mill process parameters. The particle morphology and chemical homogeneity studies were done by scanning electron microscope along with energy dispersive spectroscopy. The influence of Mo variation in the CoCrNiTiMox high entropy alloy in phase formation and crystal structure is studied using the x-ray diffraction technique. The results reveal that the CoCrNiTiMox high entropy alloy possesses two BCC solid solution phases and the powder milled for 10 h is selected as the feedstock powder for plasma spray due to its morphology and good homogeneity of mixing. © 2022, ASM International.Item Phase evolution and high-temperature wear behavior of non-equiatomic metastable CoCrNiTiMox HEA coatings fabricated by high-velocity oxy-fuel technique(Elsevier Ltd, 2023) Addepalli, S.N.; Joladarashi, S.; Ramesh, M.R.The current research aims to enhance the tribological performance of maraging steels at high temperatures by surface modification techniques. CoCrNiTiMox (x; molar fraction, x = 0.5, 1.5) high-entropy alloy (HEA) coatings with dense lamellar microstructures were deposited onto maraging steels using high-velocity oxy-fuel spray (HVOF). In order to achieve a uniform distribution of constituent elements for thermal spray deposition, mechanical alloying was employed to synthesize the HEA feedstock. The phases and microstructure of the synthesized HEA powder, as-sprayed coatings, and worn surfaces were examined using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The as-sprayed HEA coatings exhibited metastability, with a BCC phase solid solution, NiTiO3 spinel, and an intermetallic MoNi phase for CoCrNiTiMo0.5 and Co2Mo3 phase for CoCrNiTiMo1.5. The average microhardness of CoCrNiTiMo0.5 and CoCrNiTiMo1.5 HEA coatings were 841 ± 62 HV0.3 and 952 ± 23 HV0.3, respectively. The specific wear rate and friction coefficients of CoCrNiTiMox HEA coatings exhibited a decreasing trend with an increase in temperature, owing to the formation of tribofilms on the worn surface. X-ray diffraction studies revealed the formation of NiMoO4 spinel for CoCrNiTiMo0.5 and MoO2, Co3O4 phases for CoCrNiTiMo1.5 HEA at a wear temperature of 600 °C. The investigation of worn surfaces showed a transformation in wear mechanisms from abrasive wear at room temperature to oxidative wear with mild fatigue at elevated temperatures. © 2023 Elsevier LtdItem Elevated temperature tribological performance of non-equiatomic CoCrNiTiWx high entropy alloy coatings developed by mechanical alloying and high-velocity oxy-fuel spray(Elsevier B.V., 2024) Addepalli, S.N.; Joladarashi, S.; Ramesh, M.R.High entropy alloys (HEA) have applications in multiple fields owing to their exceptional mechanical and physical properties. In the current study, mechanical alloyed CoCrNiTiWx (x; a molar fraction, x = 0.5 and 1.5) HEA feedstock powders were deposited on maraging steel substrate using high-velocity oxy-fuel spray (HVOF). The phase evolution and the microstructure of the milled powders and as-sprayed coatings were analysed by X-ray diffraction (XRD) and scanning electron microscope (SEM). The tribological behaviour of CoCrNiTiW0.5 and CoCrNiTiW1.5 HEA coatings at elevated temperatures was studied extensively using a Pin-on-Disc tribometer. The CoCrNiTiW0.5 and CoCrNiTiW1.5 HEA coatings retained the BCC solid solution phases formed during the milling stage. However, additional oxide and intermetallic phases were formed owing to the in-flight oxidation and high temperatures experienced during the HVOF deposition. The deposited coatings exhibited a lamellar structure and good mechanical bonding with the substrate. The porosities of CoCrNiTiW0.5 and CoCrNiTiW1.5 HEA coatings were found to be 1.69 ± 0.32 % and 1.51 ± 0.37 % respectively.Consequently, the CoCrNiTiW0.5 and CoCrNiTiW1.5 HEA coatings displayed average microhardness values of 863 ± 52 HV0.3 and 1025 ± 39 HV0.3, respectively. Further, the wear rates of coatings exhibited a significant reduction at elevated temperatures, owing to the formation of TiO2, NiCr2O4 oxide tribofilms for CoCrNiTiW0.5, and CoCr2O4, NiWO4, WO3 oxides for CoCrNiTiW1.5. The specific wear rate of CoCrNiTiW0.5 HEA coating dropped by 73.6 % from 22.7 ± 2.6 × 10−6 mm3/N-m to 5.99 ± 1.9 × 10−6 mm3/N-m, while CoCrNiTiW1.5 dropped by 78.8 % from 11.86 ± 3.5 × 10−6 mm3/N-m to 2.51 ± 1.5 × 10−6 mm3/N-m, with a rise in the temperature from RT to 600 °C. Likewise, The frictional coefficients of CoCrNiTiW0.5 HEA dropped from 0.504 ± 0.015 to 0.397 ± 0.005, while CoCrNiTiW1.5 HEA dropped from 0.578 ± 0.025 to 0.471 ± 0.004, with a rise in temperature from RT to 600 °C. At room temperature, the wear mechanisms of the as-sprayed CoCrNiTiWx coatings were dominated by adhesive wear. However, at elevated temperatures, a shift towards oxidative wear was observed. © 2023 Elsevier B.V.Item Microstructure, Mechanical, and Dry Sliding Wear Performance of Equimolar CoCrNiTiMo and CoCrNiTiW High-Entropy Alloy Coatings(Springer, 2025) Addepalli, S.N.; Joladarashi, S.; Ramesh, M.R.In the present investigation, mechanical alloyed CoCrNiTiMo and CoCrNiTiW equimolar HEA powders were employed as feedstock in the development of dense coatings using high-velocity oxy-fuel technique. The dry sliding wear behavior of uncoated substrate and high-entropy alloy (HEA) coatings were extensively investigated at different temperatures and loads using a pin-on-disk tribometer. The microstructures and phases of the mechanical alloyed powders, deposited coatings, and worn surfaces were thoroughly studied. The mechanical alloyed CoCrNiTiMo and CoCrNiTiW HEAs demonstrated the evolution of two BCC solid solutions. However, the deposited coatings reported the formation of additional phases, including Co3Ti intermetallic and NiTiO3 spinel. The microstructural analysis of CoCrNiTiMo and CoCrNiTiW coatings unveiled a compact lamellar structure characterized by robust mechanical interlocking to the substrate. The CoCrNiTiMo and CoCrNiTiW HEA coatings displayed porosities of 1.12 ± 0.05% and 1.39 ± 0.03%, respectively. Additionally, the microhardness assessments revealed superior values for CoCrNiTiMo and CoCrNiTiW HEA coatings, measuring at 927 ± 45 HV0.3 and 951 ± 38 HV0.3, correspondingly. The wear rate of CoCrNiTiMo HEA coating dropped by 70.5%, from 17.34 ± 2.8 × 10?6 mm3/N-m to 5.1 ± 1.6 × 10?6 mm3/N-m with an increment in the wear testing temperature from ambient to 600 °C. Concurrently, the CoCrNiTiW coating experienced a 76.3% drop in the wear rates from 15.8 ± 3.7 × 10?6 mm3/N-m to 3.73 ± 2.1 × 10?6 mm3/N-m. The significant fall in the wear rates at higher temperatures was accredited to the development of oxide tribofilms. CoCrNiTiMo exhibited discernible oxide phases, including CoMoO4, TiO2, and NiO. In contrast, its counterpart, CoCrNiTiW, generated WO3, CoWO4, and TiO2 oxides at a temperature of 600 °C. The adhesive wear at RT transitioned to predominant oxidative wear with slight fatigue and abrasive wear at high temperatures. © ASM International 2025.