Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
8 results
Search Results
Item Preparation and characterization of PPSU membranes with BiOCl nanowafers loaded on activated charcoal for oil in water separation(Taiwan Institute of Chemical Engineers, 2017) Nayak, M.C.; Isloor, A.M.; Moslehyani, A.; A.F., A.F.Bismuth oxychloride nanowafers were synthesized and loaded on activated charcoal (BiOCl-AC) and were used as a novel additive to prepare polyphenylsulfone (PPSU) ultrafiltration (UF) membranes along with polyvinylpyrrolidone (PVP) as a pore forming agent by phase inversion technique. The BiOCl nanowafers were characterized by using scanning electron microscope (SEM) and Fourier transform infrared spectroscopy (FTIR). The PPSU hybrid membranes were characterized by SEM studies. The cross sectional images of the membranes along with the elemental mapping of membrane surface were assessed by using SEM and Energy Dispersive Spectroscopy (EDS). Hydrophilicity of the membranes was evaluated by contact angle, porosity and water uptake studies. The permeability of the membranes was determined by pure water flux (PWF). Membranes were also subjected to antifouling studies using bovine serum albumin (BSA) as the standard protein for rejection studies. The membranes showed greater permeability and antifouling property with the addition of BiOCl-AC. A unique cross flow ultrafiltration method was used to study the oil rejection results of both diesel fuel and crude oil. The experimental results of oil in water separation by the membrane M-3, showed 80% rejection for diesel fuel and 90.74% rejection for crude oil. © 2017 Taiwan Institute of Chemical EngineersItem Fabrication of novel PPSU/ZSM-5 ultrafiltration hollow fiber membranes for separation of proteins and hazardous reactive dyes(Taiwan Institute of Chemical Engineers, 2018) Nayak, M.C.; Isloor, A.M.; Moslehyani, A.; Ismail, N.; A.F., A.F.Polyphenylsulfone (PPSU) based asymmetric hollow fiber membranes were prepared by the addition of different percentages of ZSM-5 particles by diffusion induced phase separation method. Polyvinylpyrrolidone (PVP) was used as a pore forming agent. The fabricated membranes were characterized by Field Emission scanning electron microscopy (FESEM), Energy Dispersive Spectroscopy (EDS), contact angle, water permeability, water uptake and by porosity measurements. Membranes filtration study was performed using different proteins namely bovine serum albumin (BSA), egg albumin (EA) and hazardous dyes like Reactive black 5 (RB-5), Reactive orange 16 (RO-16) in aqueous solutions. It was found that, addition of ZSM-5 in membrane matrix showed better dye removal capacity because of its hydrophilic and adsorptive nature. The membrane (PZ-3) with higher loading of additive exhibited rejection percentages of 100% for BSA, 95.23% for EA proteins and with reactive dyes 90.81% for RB-5 and 82.84% for RO-16 as compared to the pristine HF membrane. © 2017 Taiwan Institute of Chemical EngineersItem Antibiofouling hollow-fiber membranes for dye rejection by embedding chitosan and silver-loaded chitosan nanoparticles(Springer Verlag, 2019) Kolangare, I.M.; Isloor, A.M.; Zulhairun, Z.A.; Kulal, A.; A.F., A.F.; Siddique, I.; Asiri, A.M.The removal of toxic dyes from the wastewater and industrial effluents is a major environmental challenge. Various techniques have been employed for the removal of dyes, including the application of nano-sized adsorbents, nanocomposite membranes and photodegradation. Membrane filtration is an alterntive but suffers from drawbacks such as fouling. Here we present a simple approach for the development of antibiofouling membranes based on chitosan. The application of chitosan-based nanoparticles as additives for wastewater treatment is poorly explored. The chitosan and silver-loaded chitosan nanoparticles were synthesized by ionic gelation method and incorporated to fabricate hollow-fiber membranes by dry–wet spinning technique. The prepared membranes were characterized by morphological study, permeability test, antibiofouling study and dye rejection study. The nanocomposite hollow-fiber membranes displayed superior performance than their pristine form. The incorporation of 0.30 weight percent of the chitosan and silver-loaded chitosan nanoparticles into the hollow-fiber membranes enhanced the antifouling property with flux recovery ratio of 81.21 and 86.13%, respectively. The dye rejection results showed maximum rejection of 89.27 and 86.04% for Reactive Black 5 and Reactive Orange 16, respectively. Hence, it can be concluded that hollow-fiber membranes with silver-loaded chitosan nanoparticles are pertinent in developing antibiofouling membranes for the treatment of industrial dye effluents. © 2018, Springer Nature Switzerland AG.Item Improved separation of dyes and proteins using membranes made of polyphenylsulfone/cellulose acetate or acetate phthalate(Springer Science and Business Media Deutschland GmbH, 2020) Kumar, M.; Isloor, A.M.; Todeti, S.R.; Gnani Peer Mohamed, G.P.S.; Siddique, I.; A.F., A.F.; Asiri, A.M.Industrial wastewater often contains xenobiotics such as heavy metals, dyes and proteins, yet there is a lack of efficient cleaning methods. Therefore, here we fabricated hollow fiber membranes using polyphenylsulfone containing 1, 3 and 5 wt% of cellulose acetate and cellulose acetate phthalate by non-solvent induced phase separation. Membrane morphology was characterized by field emission scanning electron microscopy. The hydrophilicity of the membranes was measured by contact angle, water uptake and porosity measurement. The thermal miscibility of the membrane with additives was assessed by thermogravimetric analysis. Hollow fiber membranes were tested for separation of azo dyes, e.g., reactive orange 16 and reactive black 5, and of proteins: bovine serum albumin, egg albumin and pepsin. Results show increasing rejection of dyes and proteins with the content of cellulose acetate and cellulose acetate phthalate. Water permeability was 41.26 L/m2 h bar for the polyphenylsulfone membrane, 64.47 L/m2 h bar for the polyphenylsulfone/5 wt% cellulose acetate membrane and 72.60 L/m2 h bar for the polyphenylsulfone/5 wt% cellulose acetate phthalate membrane. © 2020, Springer Nature Switzerland AG.Item Removal of toxic arsenic from aqueous media using polyphenylsulfone/cellulose acetate hollow fiber membranes containing zirconium oxide(Elsevier B.V., 2020) Kumar, M.; Isloor, A.M.; Somasekhara Rao, T.; A.F., A.F.; Farnood, R.; Nambissan, P.M.G.Arsenic is one of the highly dangerous metalloid present in the polluted water, it's effective and economical removal is one of the major challenges to the researchers. It was planned to prepare hollow fiber membranes using polyphenylsulfone (PPSU) as a polymer, cellulose acetate (CA) and cellulose acetate phthalate (CAP) as additives with increased dosages (0.6, 1 and 1.5 wt%) of zirconium oxide (ZrO2) nanoparticle. The fabricated hollow fiber membranes were characterized by SEM, AFM, zeta potential, ATR-FTIR and XPS to analyze the membrane's morphologies (cross-section and surface), topography, surface charge and assessment of different functional groups. As used ZrO2 was characterized by TEM and XRD to analyze the morphology and crystallinity. The positron annihilation lifetime spectroscopy (PALS) analysis was carried out for neat and ZrO2 contained membranes, to study the expansion of free-volume in membrane morphology. Leaching studies of the used zirconium with respect to different pH from the ZrO2 contained hollow fiber membrane was also examined. The enhancement of membrane hydrophilicity was confirmed by contact angle, porosity, water uptake and pure water permeability measurements. Membranes prepared by 1 wt% of ZrO2 in PPSU/CA (PZCA-1) and 0.6 wt% of ZrO2 in PPSU/CAP (PZCAP-0.6) were proved to be efficient as arsenic removal membranes (i.e. PZCA-1 as 87.24% and PZCAP-0.6 as 70.48% and permeability of 89.94 L/m2h bar and 70.59 L/m2h bar respectively) using lab-prepared 1 ppm standard arsenic solution at pH range of 6.8 ± 0.2. Also, there is a decrease in the arsenic removal tendency was observed with the excessive dosages of ZrO2, which is due to the concentration polarization on surfaces of the membranes. Antifouling behavior of the prepared hollow fiber membranes was also studied using bovine serum albumin (BSA). © 2020Item Hydrophilic nano-aluminum oxide containing polyphenylsulfone hollow fiber membranes for the extraction of arsenic (As-V) from drinking water(Elsevier Ltd, 2021) Kumar, M.; Isloor, A.M.; Todeti, S.R.; A.F., A.F.; Farnood, R.In the present work, hollow fiber ultrafiltration membranes were fabricated by incorporating intensified dosages of nano?aluminum oxide (nano-Al2O3; 0.6 wt%, 1.0 wt% and 1.5 wt%) into cellulose acetate (CA)/polyphenylsulfone (PPSU) and cellulose acetate phthalate (CAP)/PPSU by non-solvent induced phase separation (NIPS) process. The topological structures and the morphologies were investigated using atomic force microscope (AFM) and scanning electron microscope (SEM). The crystalline and morphological structures of the nano-Al2O3 were investigated using X-ray diffraction (XRD) and transmission electron microscope (TEM) respectively. Fourier transform infra-red spectroscope (FTIR) and x-ray photoelectron spectroscopy (XPS) analysis have been carried out to validate the dosages of nano-Al2O3, CA and CAP on PPSU membranes. The membrane's surface charge measurement of 1.5 wt% of nano-Al2O3 in CA/PPSU (ALCA-1.5) was scrutinized by zeta potential analysis. Membranes removed more arsenate oxide as the removal rate from membranes ALCA-1.5 and 1.0 wt% of nano-Al2O3 in CA/PPSU (ALCA-1) was 98.67% and 94.89% with retention permeabilities of 88.41 L/m2h bar and 53.53 L/m2h bar respectively from laboratory prepared 1 ppm of aqueous arsenic solution with pH in the range 6.8 ± 0.2 at 1 bar transmembrane pressure. In addition, membrane's antifouling analysis was performed using laboratory prepared 0.8 g/L (Bovine Serum Albumin) BSA as standard protein solution. © 2021 Elsevier LtdItem Improved hydrophilic and antifouling performance of nanocomposite ultrafiltration zwitterionic polyphenylsulfone membrane for protein rejection applications(Springer Medizin, 2022) Panchami, H.R.; Isloor, A.M.; A.F., A.F.Emerging technologies for the separation of proteins employ ultrafiltration membranes that incorporate hydrophilic zwitterionic nanoparticles for enhanced performances and efficacy. In this study, the zwitterionic nanoparticles were synthesized by the simple, facile distillation–precipitation polymerization (DPP) method. The monomers [2-(methacryloyloxy)ethyl]dimethyl-(3-sulfopropyl)ammonium hydroxide (DMAPDS) and 1-vinyl-2-pyrrolidone (VA), and the crosslinker N,N’-methylenebis(acrylamide) (MBAm) are utilized for the synthesis of P(MBAm-co-DMAPDS-co-VA) nanoparticle and the synthesized nanoparticle was incorporated into polyphenylsulfone (PPSU) flat sheet membrane for the effective protein rejection application. These nanoparticles greatly influence the membrane porosity and contact angle. The hydrophilic nature of the membrane samples was improved by the hydrophilic groups present in the nanoparticle. The modified membrane exhibited the highest pure water flux of the 249.4 L m−2 h−1 than the pristine of 70.6 L m−2 h−1 and enhanced flux recovery ratio and reversible fouling by 29.7 and 11.2%, respectively. The protein rejection of bovine serum albumin, pepsin, and egg albumin was found to be 92.1, 60.4, and 80.3%, respectively. Overall the fabricated membranes are highly effective in protein separation. Graphic abstract: [Figure not available: see fulltext.]. © 2021, Islamic Azad University.Item Hydrophilic polydopamine/polyvinylpyrrolidone blended polyphenylsulfone hollow fiber membranes for the removal of arsenic-V from water(Elsevier Ltd, 2023) Kumar, M.; Isloor, A.M.; Nayak, M.C.S.; Todeti, S.R.; Padaki, M.; A.F., A.F.The demand for fresh drinking water is sky rocketing with the world's increasing population, urbanization and various industrial growth. However, toxic heavy metals and metalloids like arsenic is contaminating the drinking water. Arsenic is poisonous, carcinogenic and mutagenic for millions of population. We hereby proposing in-house fabricated novel hollow fiber membranes using polyphenylsulfone (PPSU) and pore-forming agent polyvinylpyrrolidone (PVP) along with increased concentrations of bio-inspired hydrophilic additive polydopamine (PDA) for removal of arsenic-V from the drinking water. The crystallinity of PDA was interpreted by X-ray diffraction. The morphology, topology and membrane surface chemistry of fabricated membranes were evaluated by scanning electron microscopy, atomic force microscopy, thermogravimetric analysis, fourier transform infrared spectroscopy and x-ray photoelectron spectroscopy. The results indicated that, for the PDA-contained membranes overall performance was increased in terms of membrane hydrophilic characteristics and rejection efficacy. A 3 wt% of PDA in PPSU/PVP (PDA-3) executed enhanced arsenate (As-V) removal as high as 87.15% with flux of 31.80 L/m2h, which was higher than the neat membrane (PDA-0) as 67.70% with flux of 15.07 L/m2h for 5 mL/L arsenic-V aqueous solution at 0.2 MPa transmembrane pressure. Improved antifouling properties were observed from PDA-contained hollow fiber membranes, as evidenced by the improved flux recovery ratio and superior thermal stability. The mechanical properties (tensile strength) of pristine and PDA-contained membranes was also investigated. © 2023