Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
19 results
Search Results
Item Contact Angle Measurements(Elsevier Inc., 2017) Hebbar, R.S.; Isloor, A.M.; A.F., A.F.Contact angle has been an important parameter to determine the wetting ability of the polymer membrane surface. Contact angle has gained interest in surface science in regards to its fundamental aspects and application point of view. This chapter will give an insight into fundamentals of contact angle including the theoretical backgrounds, brief history, and importance of contact angle. The various factors that affect the contact angle measurement will also be discussed. The chapter will also present contact angle hysteresis phenomena, comprising of advancing and receding contact angles along with the manifestations of contact angle hysteresis. The chapter will highlight the various methods and techniques available for the measurement of contact angle along with the comprehensive description of the methods. The chapter also covers the application contact angle on surface characterization, permeation, and antifouling nature of the membrane. © 2017 Elsevier B.V. All rights reserved.Item Enhanced hydrophilicity and salt rejection study of graphene oxide-polysulfone mixed matrix membrane(2013) Ganesh, B.M.; Isloor, A.M.; A.F., A.F.Graphene oxide (GO) dispersed polysulfone (PSf) mixed matrix membranes were prepared by wet phase inversion method. The morphology of membranes was studied using scanning electron microscope (SEM) images. The variation in hydrophilicity was studied by measuring surface wettability and water swelling experiments. The performance of membranes in terms of pure water flux and salt rejection was studied. SEM images depict enhanced macrovoids, while the contact angle data reveals that, GO incorporated membrane surface is moderately hydrophilic. Membranes exhibited improved salt rejection after GO doping. Membrane with 2000ppm GO loading has exhibited maximum of 72% Na2SO4 rejection at 4bar applied pressure. The salt rejection seems to depend on pH of the feed solution and it has been witnessed that the salt rejection showed an increasing trend with increase in the pH. © 2012 Elsevier B.V.Item Modification of PSf/PIAM membrane for improved desalination applications using Chitosan coagulation media(2013) Kumar, R.; A.F., A.F.; Kassim, M.A.; Isloor, A.M.Polysulfone (PSf)/poly (isobutylene-alt-maleic anhydride) (PIAM) nanofiltration membranes were modified by changing the coagulation bath with various concentrations of glutaraldehyde cross-linked Chitosan solutions. Further the membranes were treated with 0.1N NaOH solution in order to achieve the hydrolysis of PIAM. The morphological changes of the membranes were determined using scanning electron microscope. The blending of PSf/PIAM membrane, the incorporation of Chitosan (CS) molecules in membrane matrix and the hydrolysis of PIAM in the membrane upon alkali treatment were studied by Attenuated Total Reflectance Infra Red (ATR-IR) spectroscopy. The hydrophilicity of modified membranes was measured using the contact angle analyzer. The pressure and time dependent pure water flux of modified PSf/PIAM/CS membranes were measured and compared with PSf/PIAM membranes (after alkali treatment). The antifouling property of membranes was determined using Bovine Serum Albumin (BSA) protein rejection studies. The modified membranes showed improved hydrophilicity and reduced pore size. The order of rejection of membranes for various electrolytes was Na2SO4>MgSO4>NaCl at minimum pressure of 0.2MPa TMP. The antifouling property of modified membranes increased with an increase in the composition of Chitosan in coagulation bath and membrane M-0.8 showed a maximum fouling resistance ratio of 74%. © 2013 Elsevier B.V.Item Performance improvement of polysulfone ultrafiltration membrane using N-succinyl chitosan as additive(2013) Kumar, R.; Isloor, A.M.; A.F., A.F.; Matsuura, T.A water soluble chitosan derivative, N-succinyl chitosan (NSCS), was blended with polysulfone (PSf) in three different compositions to fabricate PSf/NSCS blend membranes. The blending of polymers was confirmed by Attenuated Total Reflectance Infra-Red (ATR-IR) spectroscopy. The membranes were characterized by Scanning Electron Microscopy (SEM) images for their cross-sectional morphology. Pure water flux, water uptake and contact angle of the PSf/NSCS blend membranes were measured and compared with the pristine polysulfone membrane. The PSf/NSCS blend membranes showed enhanced hydrophilicity and permeation fluxes compared to the pristine polysulfone membrane. The membrane antifouling property was determined by filtering the bovine serum albumin (BSA) solution. The maximum flux recovery ratio (FRR) of 70% was observed by the PSf/NSCS blend membrane with 20% NSCS content. The PSf/NSCS membranes with the PSf:NSCS ratios of 80:20 and 90:10 showed nearly the same fluxes as those of polysulfone/polyethylene glycol (PSf/PEG) blend membranes with the same compositions. The hydrophilic derivative of chitosan NSCS acted as an excellent additive in improving PSf ultrafiltration properties. © 2013 Elsevier B.V.Item Polysulfone-Chitosan blend ultrafiltration membranes: Preparation, characterization, permeation and antifouling properties(2013) Kumar, R.; Isloor, A.M.; A.F., A.F.; Abdul Rashid, S.A.; Matsuura, T.Biocompatible and naturally occurring chitosan was used as an additive for the preparation of a polysulfone ultrafiltration membrane. Two different compositions of polysulfone in N-methylpyrrolidone (NMP) and chitosan in 1% acetic acid were blended to prepare PSf-CS ultrafiltration membranes by the diffusion induced phase separation (DIPS) method. The proper blending of polysulfone and chitosan in PSf-CS membranes was confirmed by ATR-IR analysis. The surface and cross-sectional morphology of the membranes was studied by scanning electron microscopy (SEM). The membrane hydrophilicity was determined by water uptake and contact angle measurements. The PSf-CS membrane showed an enhanced hydrophilicity compared to a PSf ultrafiltration membrane. The time dependent permeation studies revealed the improved flux of PSf-CS membranes. PSf-CS membranes were subjected to bovine serum albumin (BSA) protein rejection studies. An improved antifouling property was observed for PSf-CS blend membranes as compared to pristine PSf ultrafiltration membranes. Both the permeation and antifouling properties of PSf-CS membranes increased with an increase in chitosan composition. © 2013 The Royal Society of Chemistry.Item Antifouling and performance enhancement of polysulfone ultrafiltration membranes using CaCO3 nanoparticles(2013) Nair, A.K.; Isloor, A.M.; Kumar, R.; A.F., A.F.Calcium carbonate nanoparticles were synthesized from calcium nitrate via chemical precipitation method. The nanoparticles were characterized using scanning electron microscope (SEM), Attenuated total reflectance infra red (ATR-IR) spectrum and by X-ray diffraction (XRD). These nanoparticles were used as additive for polysulfone (PSf) ultrafiltration membrane along with polyethylene glycol (PEG) as pore forming agent. The PSf hybrid membranes were characterized by ATR-IR, XRD, and SEM studies. ATR-IR and XRD results indicated the successful incorporation of the nanoparticles in the membranes. Cross sectional images of the membranes along with the elemental mapping of calcium on the membrane surface were assessed using SEM. Hydrophilicity of the membranes was evaluated in terms of contact angle measurements. The permeability of the membranes was determined by measuring the pure water flux (PWF). Membranes were also subjected to antifouling studies using bovine serum albumin (BSA) as the standard protein for rejection. The membranes showed better permeability and antifouling property with the increased addition of CaCO3 nanoparticles. © 2013 Elsevier B.V.Item Preparation and antifouling properties of PVDF ultrafiltration membranes with polyaniline (PANI) nanofibers and hydrolysed PSMA (H-PSMA) as additives(Elsevier, 2014) Pereira, V.R.; Isloor, A.M.; Bhat, K.U.; A.F., A.F.Polyaniline (PANI) nanofibers were used as hydrophilic additives to study their effect on the performance of polyvinylidene fluoride (PVDF) ultrafiltration (UF) membranes. PVDF UF membranes were prepared by the phase inversion method with hydrolyzed polystyrene-co-maleic anhydride (H-PSMA) and PANI nanofibers as additives. PANI nanofibers were synthesized by rapid mixing reaction and were used as a hydrophilic modifying agent with varying concentrations (0-1.5 wt.%) in the membranes. The synthesized PANI nanofibers were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM) analysis. Hydrolyzed PSMA was prepared by the hydrolysis of PSMA and was used as a novel pore forming additive. The addition of PANI nanofibers into the membranes increased the membrane hydrophilicity, porosity, water uptake and permeability. The membranes also showed good antifouling nature during BSA (bovine serum albumin) filtration when compared to the pristine membrane without PANI nanofibers. Membrane with 1.0 wt.% PANI content showed highest permeability among the synthesized membranes. The membrane having highest permeability was subjected to heavy metal ion rejection which showed high rejection of 98.52% and 97.38% for heavy metal ions Pb2+ and Cd2+ respectively. © 2014 Elsevier B.V.Item Preparation and characterization of novel PSf/PVP/PANI-nanofiber nanocomposite hollow fiber ultrafiltration membranes and their possible applications for hazardous dye rejection(Elsevier, 2015) Kajekar, A.J.; Dodamani, B.M.; Isloor, A.M.; Zulhairun, A.K.; Cheer, N.B.; A.F., A.F.; Shilton, S.J.In the present study, PANI (polyaniline)-nanofibers were synthesized by interfacial polymerization technique, dispersed in n-Methyl-2-Pyrrolidone (NMP) solvent and blended with PVP (Polyvinylpyrrolidone)/PSf (Polysulfone) for preparing the novel hollow fiber membrane by dry-wet spinning technique. The newly prepared nanocomposite ultrafiltration hollow fiber membrane is characterized by Scanning Electron Microscope (SEM), Contact Angle, Zeta Potential and Differential Scanning Calorimeter (DSC). Filtration studies are conducted to measure the membrane pure water flux (PWF), rejection of hazardous dye (Reactive Red 120) and fouling resistance. The maximum rejections are obtained for M 0.5 membrane with 99.25% rejection of RR120 hazardous dye at 2. bar pressure. The pure water flux, percentage rejection, antifouling property and thermal resistance increased with an increase in PANI-nanofiber concentration. The contact angle of the membrane decreased with increasing PANI-nanofiber concentration, which indicated increased hydrophilicity of the new membranes. © 2015 Elsevier B.V.Item Fabrication of polydopamine functionalized halloysite nanotube/polyetherimide membranes for heavy metal removal(Royal Society of Chemistry, 2016) Hebbar, R.S.; Isloor, A.M.; Kulal, K.; A.F., A.F.Polydopamine modified halloysite nanotubes (HNTs) were synthesised through a one step facile procedure and employed as a well dispersed hydrophilic additive to enhance the filtration properties of polyetherimide (PEI) membranes. The nanocomposite membranes were prepared by an immersion precipitation method with different amounts of modified HNTs (MHNTs) in the casting solution. The good dispersion of MHNTs throughout the membrane matrix was confirmed by elemental mapping analysis. The prepared nanocomposite membranes were extensively studied in terms of their porosity, morphology, membrane hydraulic resistance and hydrophilicity. The permeation experiments showed that the modified membranes exhibited higher water flux than a pristine PEI membrane. The antifouling and anti-biofouling behaviour of the modified membranes was investigated in detail. The results revealed that a membrane with a 3 wt% MHNT dosage showed a higher Fouling Resistance Ratio (FRR) of 74.5% with reversible membrane fouling of 64.3%. Moreover, the membrane showed excellent resistance to microbial growth on the membrane surface. The well performing membrane was subjected to heavy metal ion rejection. Results indicated that membranes had the capacity to adsorb Pb2+ and Cd2+. Overall, PEI-MHNTs nanocomposite membranes could have great potential to improve antifouling, anti-biofouling and filtration properties. © The Royal Society of Chemistry 2016.Item Novel mixed matrix membranes incorporated with dual-nanofillers for enhanced oil-water separation(Elsevier B.V., 2017) Lai, G.S.; Yusob, M.H.M.; Lau, W.J.; Jamshidi Gohari, R.J.; Emadzadeh, D.; A.F., A.F.; Goh, P.S.; Isloor, A.M.; Arzhandi, M.R.-D.In this work, a new type of mixed matrix membranes (MMMs) composed of dual-nanofillers at different ratios of hydrous manganese oxide (HMO) and titanium dioxide (TiO2) was fabricated with the objective of improving properties of polyethersulfone (PSF)-based membrane for oil-water separation process. The morphology and surface chemistry of the resultant MMMs were characterized by several analytical instruments, i.e., SEM-EDX, contact angle goniometer and FTIR spectrometer prior to separation performance evaluation using oily solution composed of 500 or 2000 ppm. The results showed that the membrane surface hydrophilicity was greatly improved upon addition of hydrophilic nanofillers and HMO in particular showed greater extent of hydrophilicity enhancement owing to the fact that it is associated with higher amount of [sbnd]OH functional groups compared to TiO2. The improved surface hydrophilicity coupled with formation of long finger-like voids in the membrane structure are the main factors leading to greater water flux of MMMs in comparison to control PES membrane. MMM2 (membrane made of HMO:TiO2ratio of 0.75:0.25) and MMM4 (HMO:TiO2ratio of 0.25:0.75) in particular were the best two performing nanofillers-incorporated membranes owing to their good balance between water flux and oil removal rate. They achieved 31.73% and 26.41% higher water flux than that of the control membrane without sacrificing oil removal rate. Most importantly, these nanofillers-incorporated membranes showed significantly lower degree of flux decline as a result of improved surface resistance against oil fouling and are of potential for long-term operation with extended lifespan. © 2017 Elsevier B.V.