Faculty Publications
Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736
Publications by NITK Faculty
Browse
11 results
Search Results
Item Enhanced permeation performance of cellulose acetate ultrafiltration membranes by incorporation of sulfonated poly(1,4-phenylene ether ether sulfone) and poly(styrene- Co -maleic anhydride)(American Chemical Society service@acs.org, 2014) Shenvi, S.; A.F., A.F.; Isloor, A.M.A cellulose acetate (CA)-based ultrafiltration membrane was prepared by incorporation of mechanically strong, sulfonated poly(1,4-phenylene ether ether sulfone) (SPEES) to which hydrolyzed poly(styrene-co-maleic anhydride) (PSMA) was added as a novel additive. The preparation of SPEES was investigated in detail. SPEES having a degree of sulfonation of 21%, was more suitable for the blend. The chemical constitutions of SPEES, PSMA, and the blend membranes were confirmed by attenuated total reflectance fourier transform infrared spectroscopy. The scanning electron microscopy images revealed finger-like projections in the membrane structure. The performance of the membranes was analyzed on the basis of water content, porosity, flux, and antifouling studies. A membrane comprising 30% SPEES and 2% additive showed superior performance with flux and flux recovery ratio of 228 L/(m2 h) and 91%, respectively. It was concluded that the prepared membranes showed better performance in comparison with neat CA membranes. © 2014 American Chemical Society.Item Preparation and antifouling properties of PVDF ultrafiltration membranes with polyaniline (PANI) nanofibers and hydrolysed PSMA (H-PSMA) as additives(Elsevier, 2014) Pereira, V.R.; Isloor, A.M.; Bhat, K.U.; A.F., A.F.Polyaniline (PANI) nanofibers were used as hydrophilic additives to study their effect on the performance of polyvinylidene fluoride (PVDF) ultrafiltration (UF) membranes. PVDF UF membranes were prepared by the phase inversion method with hydrolyzed polystyrene-co-maleic anhydride (H-PSMA) and PANI nanofibers as additives. PANI nanofibers were synthesized by rapid mixing reaction and were used as a hydrophilic modifying agent with varying concentrations (0-1.5 wt.%) in the membranes. The synthesized PANI nanofibers were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM) analysis. Hydrolyzed PSMA was prepared by the hydrolysis of PSMA and was used as a novel pore forming additive. The addition of PANI nanofibers into the membranes increased the membrane hydrophilicity, porosity, water uptake and permeability. The membranes also showed good antifouling nature during BSA (bovine serum albumin) filtration when compared to the pristine membrane without PANI nanofibers. Membrane with 1.0 wt.% PANI content showed highest permeability among the synthesized membranes. The membrane having highest permeability was subjected to heavy metal ion rejection which showed high rejection of 98.52% and 97.38% for heavy metal ions Pb2+ and Cd2+ respectively. © 2014 Elsevier B.V.Item Preparation and performance studies of polysulfone-sulfated nano-titania (S-TiO2) nanofiltration membranes for dye removal(Royal Society of Chemistry, 2015) Pereira, V.R.; Isloor, A.M.; Bhat, K.U.; A.F., A.F.; AlObaid, A.; Fun, H.-K.Polysulfone nanofiltration membranes containing sulfated nano-titania (S-TiO2) were fabricated, with the aim to enhance the membrane properties along with the possible rejection of Methylene Blue (MB) dye by membranes. Initially S-TiO2 was synthesized from nano TiO2 by the action of sulfuric acid. The synthesized S-TiO2 was characterized by Fourier Transform Infrared spectroscopy (FT-IR), Energy Dispersive Spectrophotometry (EDS) and Transmission Electron Microscopy (TEM) analysis. S-TiO2 was added in increasing concentrations into the membranes and its effect on the performance of the membranes was evaluated. The synthesized membranes were characterized by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). Polysulfone membranes containing S-TiO2 showed enhancement in properties in terms of hydrophilicity, water uptake, mechanical strength, improved pure water flux (PWF), antifouling nature and high Flux Recovery Ratio (FRR). The polysulfone membranes with S-TiO2 showed 99% rejection for BSA (Bovine Serum Albumin) protein molecules during BSA filtration. The prepared membranes were used for the removal of MB dye from aqueous solutions. A maximum of 90.4% rejection was obtained for MB for the membrane having 2.0 wt% of S-TiO2 under UV light radiation. This approach showed that polysulfone-S-TiO2 membranes displayed good efficiency for dye removal and can be effectively used for the removal of MB dye from aqueous solutions under suitable conditions. © The Royal Society of Chemistry.Item Novel hybrid photocatalytic reactor-UF nanocomposite membrane system for bilge water degradation and separation(Royal Society of Chemistry, 2015) Moslehyani, A.; A.F., A.F.; Othman, M.H.D.; Isloor, A.M.This study focuses on the design and performance of a hybrid system consisting of a photocatalytic reactor and ultrafiltration permeation cell. Initially, an ultraviolet (UV) lamp was installed in the photocatalytic reactor to decompose the bilge organic pollutants in the presence of 200 ppm titanium-dioxide (TiO2). Individual hydrocarbon compounds of bilge water samples were identified by gas chromatography-mass spectrometry (GC-MS) analysis. Two types of membrane, which are a pure polyvinylidene fluoride (PVDF) membrane and PVDF/modified halloysite nanotube clay (M-HNTs) nanocomposite membrane were fabricated aiming to enhance the rejection, flux and fouling resistance for full filtration of pollutants from the photocatalytic reactor. The membranes were characterized by Fourier transform infrared (FTIR), field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM). Furthermore, GC-MS analysis showed that, over 90% bilge decomposition occurred by a photocatalytic reaction. The TiO2 cross-over during permeation was detected by using an atomic absorption spectrophotometer (AAS), which proved that, TiO2 rejection was more than 99% for the nanocomposite membrane. A UV- vis spectrophotometer confirmed over 99% rejection of decomposed bilge hydrocarbons via the nanocomposite membrane with 1.0 wt% of M-HNTs incorporated in the PVDF matrix. This journal is © The Royal Society of Chemistry 2015.Item Humic Acid Based Biopolymeric Membrane for Effective Removal of Methylene Blue and Rhodamine B(American Chemical Society service@acs.org, 2015) Shenvi, S.S.; Isloor, A.M.; A.F., A.F.; Shilton, S.J.; Al-Ahmed, A.Humic acid was immobilized on a polypropylene supported sodium alginate/hydroxyethyl cellulose blend membrane in the current work. The adsorption property of this membrane for the removal of cationic dyes, namely, methylene blue (MB) and rhodamine B (RhB), was extensively studied. Batch-adsorption experiments were conducted to investigate the adsorption behavior of dyes on the membrane with variation in adsorbent mass, initial dye concentration, pH, time, and temperature. The membranes were characterized by scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX), Fourier transform infrared spectroscopy (FTIR), and atomic force microscopy (AFM). Prepared membranes showed more than 98% removal capacity for both dyes under optimal conditions. Kinetic experiments revealed that the pseudo second order model exhibited the best correlation with the adsorption data. Dubinin-Radushkevich model indicated that the adsorption of dyes onto the membrane surface was by simple physisorption. The membrane was easily regenerated by simple acid treatment, and its efficiency remained significant even after four adsorption cycles. © 2015 American Chemical Society.Item Preparation and characterization of PPSU membranes with BiOCl nanowafers loaded on activated charcoal for oil in water separation(Taiwan Institute of Chemical Engineers, 2017) Nayak, M.C.; Isloor, A.M.; Moslehyani, A.; A.F., A.F.Bismuth oxychloride nanowafers were synthesized and loaded on activated charcoal (BiOCl-AC) and were used as a novel additive to prepare polyphenylsulfone (PPSU) ultrafiltration (UF) membranes along with polyvinylpyrrolidone (PVP) as a pore forming agent by phase inversion technique. The BiOCl nanowafers were characterized by using scanning electron microscope (SEM) and Fourier transform infrared spectroscopy (FTIR). The PPSU hybrid membranes were characterized by SEM studies. The cross sectional images of the membranes along with the elemental mapping of membrane surface were assessed by using SEM and Energy Dispersive Spectroscopy (EDS). Hydrophilicity of the membranes was evaluated by contact angle, porosity and water uptake studies. The permeability of the membranes was determined by pure water flux (PWF). Membranes were also subjected to antifouling studies using bovine serum albumin (BSA) as the standard protein for rejection studies. The membranes showed greater permeability and antifouling property with the addition of BiOCl-AC. A unique cross flow ultrafiltration method was used to study the oil rejection results of both diesel fuel and crude oil. The experimental results of oil in water separation by the membrane M-3, showed 80% rejection for diesel fuel and 90.74% rejection for crude oil. © 2017 Taiwan Institute of Chemical EngineersItem Use of cellulose acetate/polyphenylsulfone derivatives to fabricate ultrafiltration hollow fiber membranes for the removal of arsenic from drinking water(Elsevier B.V., 2019) Kumar, M.; Todeti, S.; Isloor, A.M.; Gnani Peer Mohamed, G.P.S.; Siddique, I.; Ismail, N.I.; A.F., A.F.; Asiri, A.M.Cellulose acetate (CA) and cellulose acetate phthalate (CAP) were used as additives (1 wt%, 3 wt%, and 5 wt%) to prepare polyphenylsulfone (PPSU) hollow fiber membranes. Prepared hollow fiber membranes were characterized by surface morphology using scanning electron microscopy (SEM), surface roughness by atomic force microscopy (AFM), the surface charge of the membrane was analyzed by zeta potential measurement, hydrophilicity by contact angle measurement and the functional groups by fourier transform infrared spectroscopy (FTIR). Fouling resistant nature of the prepared hollow fiber membranes was evaluated by bovine serum albumin (BSA) and molecular weight cutoff was investigated using polyethylene glycol (PEG). By total organic carbon (TOC), the percentage rejection of PEG was found to be 14,489 Da. It was found that the hollow fiber membrane prepared by the addition of 5 wt% of CAP in PPSU confirmed increased arsenic removal from water as compared to hollow fiber membrane prepared by 5 wt% of CA in PPSU. The removal percentages of arsenic with CA-5 and CAP-5 hollow fiber membrane was 34% and 41% with arsenic removal permeability was 44.42 L/m2h bar and 40.11 L/m2h bar respectively. The increased pure water permeability for CA-5 and CAP-5 hollow fiber membrane was 61.47 L/m2h bar and 69.60 L/m2 h bar, respectively. © 2019 Elsevier B.V.Item Removal of toxic arsenic from aqueous media using polyphenylsulfone/cellulose acetate hollow fiber membranes containing zirconium oxide(Elsevier B.V., 2020) Kumar, M.; Isloor, A.M.; Somasekhara Rao, T.; A.F., A.F.; Farnood, R.; Nambissan, P.M.G.Arsenic is one of the highly dangerous metalloid present in the polluted water, it's effective and economical removal is one of the major challenges to the researchers. It was planned to prepare hollow fiber membranes using polyphenylsulfone (PPSU) as a polymer, cellulose acetate (CA) and cellulose acetate phthalate (CAP) as additives with increased dosages (0.6, 1 and 1.5 wt%) of zirconium oxide (ZrO2) nanoparticle. The fabricated hollow fiber membranes were characterized by SEM, AFM, zeta potential, ATR-FTIR and XPS to analyze the membrane's morphologies (cross-section and surface), topography, surface charge and assessment of different functional groups. As used ZrO2 was characterized by TEM and XRD to analyze the morphology and crystallinity. The positron annihilation lifetime spectroscopy (PALS) analysis was carried out for neat and ZrO2 contained membranes, to study the expansion of free-volume in membrane morphology. Leaching studies of the used zirconium with respect to different pH from the ZrO2 contained hollow fiber membrane was also examined. The enhancement of membrane hydrophilicity was confirmed by contact angle, porosity, water uptake and pure water permeability measurements. Membranes prepared by 1 wt% of ZrO2 in PPSU/CA (PZCA-1) and 0.6 wt% of ZrO2 in PPSU/CAP (PZCAP-0.6) were proved to be efficient as arsenic removal membranes (i.e. PZCA-1 as 87.24% and PZCAP-0.6 as 70.48% and permeability of 89.94 L/m2h bar and 70.59 L/m2h bar respectively) using lab-prepared 1 ppm standard arsenic solution at pH range of 6.8 ± 0.2. Also, there is a decrease in the arsenic removal tendency was observed with the excessive dosages of ZrO2, which is due to the concentration polarization on surfaces of the membranes. Antifouling behavior of the prepared hollow fiber membranes was also studied using bovine serum albumin (BSA). © 2020Item Effect of binary zinc-magnesium oxides on polyphenylsulfone/cellulose acetate derivatives hollow fiber membranes for the decontamination of arsenic from drinking water(Elsevier B.V., 2021) Kumar, M.; Isloor, A.M.; Todeti, S.R.; Nagaraja, H.S.; A.F., A.F.; Susanti, R.Arsenic contamination is continuously threatening the safety of drinking water in many parts of the world. The consumption of chronic arsenic contaminated drinking water can cause serious health related issues. Therefore, the synthesis of novel materials is very much essential for the selective removal of arsenic from aqueous solution. In the present investigation, the effect of increased concentrations (0.6, 1.0 and 1.5 wt%) of binary zinc-magnesium oxide (ZnO-MgO) on cellulose acetate (CA)/polyphenylsulfone (PPSU) and cellulose acetate phthalate (CAP)/PPSU hollow fiber membranes for arsenic removal was performed. As used ZnO-MgO was characterized by using x-ray diffraction (XRD), transmission electron microscopy (TEM) and particle size distribution. Fabricated hollow fiber membranes were characterized using scanning electron microscopy (SEM), atomic force microscopy (AFM), zeta potential, fourier transform infrared (FTIR), x-ray photoelectron spectrophotometer (XPS), thermogravimetric analysis (TGA) and antifouling studies. The results revealed that, there is significant enhancement in the overall performance of the ZnO-MgO containedmembranes. An enhancement of arsenic removal properties was demonstrated from 0.6 wt% of ZnO-MgO in CAP/PPSU (ZMCAP-0.6) membrane was 81.31% with the retention permeability of 69.58 L/m2h bar respectively. Similarly, 1 wt% of ZnO-MgO in CA/PPSU (ZMCA-1) was found to be 78.48% and 198.47 L/m2h bar respectively using 1 ppm laboratory prepared aqueous arsenic solution (pH 6.8 ± 0.2) at 1 bar transmembrane pressure. In addition, improved antifouling properties was noticed with an increased flux recovery ratio and enhanced thermal stability from ZnO-MgO contained membranes. Therefore, as fabricated ZnO-MgO contained membranes provided enhanced arsenic removal tendency without compromising the retention permeability. © 2020Item Hydrophilic polydopamine/polyvinylpyrrolidone blended polyphenylsulfone hollow fiber membranes for the removal of arsenic-V from water(Elsevier Ltd, 2023) Kumar, M.; Isloor, A.M.; Nayak, M.C.S.; Todeti, S.R.; Padaki, M.; A.F., A.F.The demand for fresh drinking water is sky rocketing with the world's increasing population, urbanization and various industrial growth. However, toxic heavy metals and metalloids like arsenic is contaminating the drinking water. Arsenic is poisonous, carcinogenic and mutagenic for millions of population. We hereby proposing in-house fabricated novel hollow fiber membranes using polyphenylsulfone (PPSU) and pore-forming agent polyvinylpyrrolidone (PVP) along with increased concentrations of bio-inspired hydrophilic additive polydopamine (PDA) for removal of arsenic-V from the drinking water. The crystallinity of PDA was interpreted by X-ray diffraction. The morphology, topology and membrane surface chemistry of fabricated membranes were evaluated by scanning electron microscopy, atomic force microscopy, thermogravimetric analysis, fourier transform infrared spectroscopy and x-ray photoelectron spectroscopy. The results indicated that, for the PDA-contained membranes overall performance was increased in terms of membrane hydrophilic characteristics and rejection efficacy. A 3 wt% of PDA in PPSU/PVP (PDA-3) executed enhanced arsenate (As-V) removal as high as 87.15% with flux of 31.80 L/m2h, which was higher than the neat membrane (PDA-0) as 67.70% with flux of 15.07 L/m2h for 5 mL/L arsenic-V aqueous solution at 0.2 MPa transmembrane pressure. Improved antifouling properties were observed from PDA-contained hollow fiber membranes, as evidenced by the improved flux recovery ratio and superior thermal stability. The mechanical properties (tensile strength) of pristine and PDA-contained membranes was also investigated. © 2023