Faculty Publications

Permanent URI for this communityhttps://idr.nitk.ac.in/handle/123456789/18736

Publications by NITK Faculty

Browse

Author: search.filters.author.A.F., A.F.Subject: search.filters.subject.Antifouling property

Search Results

Now showing 1 - 6 of 6
  • No Thumbnail Available
    Item
    Permeation, Antifouling and desalination performance of TiO2 nanotube incorporated PSf/CS blend membranes
    (2013) Kumar, R.; Isloor, A.M.; A.F., A.F.; Abdul Rashid, S.A.; Ahmed, A.A.
    Polysulfone (PSf) and chitosan (CS) blend membranes were prepared by incorporating titanium dioxide nanotubes (TiO2NT) in different compositions. The proper blending of PSf and CS in the PSf/CS/TiO2 membranes was confirmed by ATR-IR spectroscopy. The influence of nanotubes on morphology of membranes was investigated by Field Emission Scanning Electron Microscopy (FESEM). The effect of nanotubes on hydrophilicity of the membranes was studied by water swelling and contact angle measurements. The distribution of TiO2NT on the membrane surface was determined by Transmission Electron Microscope (TEM) analysis. The permeation property of PSf/CS/TiO2NT membranes was carried out by measuring the time dependent pure water flux (PWF). Bovine serum albumin (BSA) protein rejection studies were performed to know the antifouling properties. The rheological percolation threshold of PSf/CS/TiO2NT solutions was measured by viscosity studies. The nanotubes incorporated PSf/CS membranes showed enhanced permeation and antifouling properties compared to PSf/CS and nascent PSf ultrafiltration membranes. Membranes prepared well above rheological percolation threshold showed drastic reduction in pore size and acted as nanofiltration (NF) membranes. © 2013 Elsevier B.V.
  • No Thumbnail Available
    Item
    Polysulfone-Chitosan blend ultrafiltration membranes: Preparation, characterization, permeation and antifouling properties
    (2013) Kumar, R.; Isloor, A.M.; A.F., A.F.; Abdul Rashid, S.A.; Matsuura, T.
    Biocompatible and naturally occurring chitosan was used as an additive for the preparation of a polysulfone ultrafiltration membrane. Two different compositions of polysulfone in N-methylpyrrolidone (NMP) and chitosan in 1% acetic acid were blended to prepare PSf-CS ultrafiltration membranes by the diffusion induced phase separation (DIPS) method. The proper blending of polysulfone and chitosan in PSf-CS membranes was confirmed by ATR-IR analysis. The surface and cross-sectional morphology of the membranes was studied by scanning electron microscopy (SEM). The membrane hydrophilicity was determined by water uptake and contact angle measurements. The PSf-CS membrane showed an enhanced hydrophilicity compared to a PSf ultrafiltration membrane. The time dependent permeation studies revealed the improved flux of PSf-CS membranes. PSf-CS membranes were subjected to bovine serum albumin (BSA) protein rejection studies. An improved antifouling property was observed for PSf-CS blend membranes as compared to pristine PSf ultrafiltration membranes. Both the permeation and antifouling properties of PSf-CS membranes increased with an increase in chitosan composition. © 2013 The Royal Society of Chemistry.
  • No Thumbnail Available
    Item
    Preparation and antifouling properties of PVDF ultrafiltration membranes with polyaniline (PANI) nanofibers and hydrolysed PSMA (H-PSMA) as additives
    (Elsevier, 2014) Pereira, V.R.; Isloor, A.M.; Bhat, K.U.; A.F., A.F.
    Polyaniline (PANI) nanofibers were used as hydrophilic additives to study their effect on the performance of polyvinylidene fluoride (PVDF) ultrafiltration (UF) membranes. PVDF UF membranes were prepared by the phase inversion method with hydrolyzed polystyrene-co-maleic anhydride (H-PSMA) and PANI nanofibers as additives. PANI nanofibers were synthesized by rapid mixing reaction and were used as a hydrophilic modifying agent with varying concentrations (0-1.5 wt.%) in the membranes. The synthesized PANI nanofibers were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM) analysis. Hydrolyzed PSMA was prepared by the hydrolysis of PSMA and was used as a novel pore forming additive. The addition of PANI nanofibers into the membranes increased the membrane hydrophilicity, porosity, water uptake and permeability. The membranes also showed good antifouling nature during BSA (bovine serum albumin) filtration when compared to the pristine membrane without PANI nanofibers. Membrane with 1.0 wt.% PANI content showed highest permeability among the synthesized membranes. The membrane having highest permeability was subjected to heavy metal ion rejection which showed high rejection of 98.52% and 97.38% for heavy metal ions Pb2+ and Cd2+ respectively. © 2014 Elsevier B.V.
  • No Thumbnail Available
    Item
    Preparation and characterization of novel PSf/PVP/PANI-nanofiber nanocomposite hollow fiber ultrafiltration membranes and their possible applications for hazardous dye rejection
    (Elsevier, 2015) Kajekar, A.J.; Dodamani, B.M.; Isloor, A.M.; Zulhairun, A.K.; Cheer, N.B.; A.F., A.F.; Shilton, S.J.
    In the present study, PANI (polyaniline)-nanofibers were synthesized by interfacial polymerization technique, dispersed in n-Methyl-2-Pyrrolidone (NMP) solvent and blended with PVP (Polyvinylpyrrolidone)/PSf (Polysulfone) for preparing the novel hollow fiber membrane by dry-wet spinning technique. The newly prepared nanocomposite ultrafiltration hollow fiber membrane is characterized by Scanning Electron Microscope (SEM), Contact Angle, Zeta Potential and Differential Scanning Calorimeter (DSC). Filtration studies are conducted to measure the membrane pure water flux (PWF), rejection of hazardous dye (Reactive Red 120) and fouling resistance. The maximum rejections are obtained for M 0.5 membrane with 99.25% rejection of RR120 hazardous dye at 2. bar pressure. The pure water flux, percentage rejection, antifouling property and thermal resistance increased with an increase in PANI-nanofiber concentration. The contact angle of the membrane decreased with increasing PANI-nanofiber concentration, which indicated increased hydrophilicity of the new membranes. © 2015 Elsevier B.V.
  • No Thumbnail Available
    Item
    Effect of binary zinc-magnesium oxides on polyphenylsulfone/cellulose acetate derivatives hollow fiber membranes for the decontamination of arsenic from drinking water
    (Elsevier B.V., 2021) Kumar, M.; Isloor, A.M.; Todeti, S.R.; Nagaraja, H.S.; A.F., A.F.; Susanti, R.
    Arsenic contamination is continuously threatening the safety of drinking water in many parts of the world. The consumption of chronic arsenic contaminated drinking water can cause serious health related issues. Therefore, the synthesis of novel materials is very much essential for the selective removal of arsenic from aqueous solution. In the present investigation, the effect of increased concentrations (0.6, 1.0 and 1.5 wt%) of binary zinc-magnesium oxide (ZnO-MgO) on cellulose acetate (CA)/polyphenylsulfone (PPSU) and cellulose acetate phthalate (CAP)/PPSU hollow fiber membranes for arsenic removal was performed. As used ZnO-MgO was characterized by using x-ray diffraction (XRD), transmission electron microscopy (TEM) and particle size distribution. Fabricated hollow fiber membranes were characterized using scanning electron microscopy (SEM), atomic force microscopy (AFM), zeta potential, fourier transform infrared (FTIR), x-ray photoelectron spectrophotometer (XPS), thermogravimetric analysis (TGA) and antifouling studies. The results revealed that, there is significant enhancement in the overall performance of the ZnO-MgO containedmembranes. An enhancement of arsenic removal properties was demonstrated from 0.6 wt% of ZnO-MgO in CAP/PPSU (ZMCAP-0.6) membrane was 81.31% with the retention permeability of 69.58 L/m2h bar respectively. Similarly, 1 wt% of ZnO-MgO in CA/PPSU (ZMCA-1) was found to be 78.48% and 198.47 L/m2h bar respectively using 1 ppm laboratory prepared aqueous arsenic solution (pH 6.8 ± 0.2) at 1 bar transmembrane pressure. In addition, improved antifouling properties was noticed with an increased flux recovery ratio and enhanced thermal stability from ZnO-MgO contained membranes. Therefore, as fabricated ZnO-MgO contained membranes provided enhanced arsenic removal tendency without compromising the retention permeability. © 2020
  • No Thumbnail Available
    Item
    Hydrophilic polydopamine/polyvinylpyrrolidone blended polyphenylsulfone hollow fiber membranes for the removal of arsenic-V from water
    (Elsevier Ltd, 2023) Kumar, M.; Isloor, A.M.; Nayak, M.C.S.; Todeti, S.R.; Padaki, M.; A.F., A.F.
    The demand for fresh drinking water is sky rocketing with the world's increasing population, urbanization and various industrial growth. However, toxic heavy metals and metalloids like arsenic is contaminating the drinking water. Arsenic is poisonous, carcinogenic and mutagenic for millions of population. We hereby proposing in-house fabricated novel hollow fiber membranes using polyphenylsulfone (PPSU) and pore-forming agent polyvinylpyrrolidone (PVP) along with increased concentrations of bio-inspired hydrophilic additive polydopamine (PDA) for removal of arsenic-V from the drinking water. The crystallinity of PDA was interpreted by X-ray diffraction. The morphology, topology and membrane surface chemistry of fabricated membranes were evaluated by scanning electron microscopy, atomic force microscopy, thermogravimetric analysis, fourier transform infrared spectroscopy and x-ray photoelectron spectroscopy. The results indicated that, for the PDA-contained membranes overall performance was increased in terms of membrane hydrophilic characteristics and rejection efficacy. A 3 wt% of PDA in PPSU/PVP (PDA-3) executed enhanced arsenate (As-V) removal as high as 87.15% with flux of 31.80 L/m2h, which was higher than the neat membrane (PDA-0) as 67.70% with flux of 15.07 L/m2h for 5 mL/L arsenic-V aqueous solution at 0.2 MPa transmembrane pressure. Improved antifouling properties were observed from PDA-contained hollow fiber membranes, as evidenced by the improved flux recovery ratio and superior thermal stability. The mechanical properties (tensile strength) of pristine and PDA-contained membranes was also investigated. © 2023