Journal Articles
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/19884
Browse
41 results
Search Results
Item Shape optimization of steel reinforced concrete beams(Techno Press, 2007) Babu Narayan, K.S.B.; Venkataramana, K.Steel reinforced concrete is perhaps the most versatile and widely used construction material. The versatility is attributed to mouldability of concrete to any conceivable shape. The inherent property of cracking of concrete is the reason for its low tensile strength and hence the design approach of RCC sections in flexure adopts the cracked section theory where in concrete in tension zone is ignored. Means, modes and methods of exploitation of concrete strength by conceiving shapes other than rectangular whereby ineffective concrete in tension zone is reduced and incorporated in compression zone where it is effective needs consideration. Shape optimization of beams is attempted in this analytical investigation employing Sequential Unconstrained Minimization Technique (SUMT). The results clearly show that trapezoidal beams happen to be less costlier than their rectangular counterparts, their usage needs serious reconsideration by the designers.Item Coastal vulnerability assessment of the future sea level rise in Udupi coastal zone of Karnataka state, west coast of India(2009) Dwarakish, G.S.; Vinay, S.A.; Natesan, U.; Asano, T.; Kakinuma, T.; Venkataramana, K.; Pai, B.J.; Babita, M.K.Udupi coast in Karnataka state, along the west coast of India, selected as a study area, is well known for sandy beaches, aquaculture ponds, lush greenery, temples and major and minor industries. It lies between 13°00?00?-13°45?00? north latitudes and 74°47?30?-74°30?00? east longitudes, the length of the coastline is 95 km, and is oriented along the NNW-SSE direction. It is vulnerable to accelerated sea level rise (SLR) due to its low topography and its high ecological and touristy value. The present study has been carried out with a view to calculate the coastal vulnerability index (CVI) to know the high and low vulnerable areas and area of inundation due to future SLR, and land loss due to coastal erosion. Both conventional and remotely sensed data were used and analysed through the modelling technique and by using ERDAS Imagine and geographical information system software. The rate of erosion was 0.6018 km2/yr during 2000-2006 and around 46 km of the total 95 km stretch is under critical erosion. Out of the 95 km stretch coastline, 59% is at very high risk, 7% high, 4% moderate and 30% in the low vulnerable category, due to SLR. Results of the inundation analysis indicate that 42.19 km2 and 372.08 km2 of the land area will be submerged by flooding at 1 m and 10 m inundation levels. The most severely affected sectors are expected to be the residential and recreational areas, agricultural land, and the natural ecosystem. As this coast is planned for future coastal developmental activities, measures such as building regulation, urban growth planning, development of an integrated coastal zone management, strict enforcement of the Coastal Regulation Zone (CRZ) Act 1991, monitoring of impacts and further research in this regard are recommended for the study area. © 2009 Elsevier Ltd. All rights reserved.Item Influence of masonry infill on fundamental natural frequency of 2D RC frames(2010) Chethan, K.; Ramesh Babu, R.; Venkataramana, K.; Sharma, A.Reinforced Concrete (RC) framed structures with Un-Reinforced Masonry (URM) infill panels form a major portion of all the RC framed structures worldwide. The URM panels are considered as non-structural members, which is fairly good assumption under gravity loads, however, it is not the same under lateral forces. Under seismic loads, the stiffness additions due to infill panels modify the dynamic behavior of the structure significantly by altering the frequency of the structure. A research project has been taken up at Earthquake Engineering and Vibration Research Centre (EVRC), Central Power Research Institute (CPRI), Bangalore to investigate the influence of masonry infill on fundamental natural frequency of RC frames. 2D RC frames of one bay and two bay having single storey, double storey and three storeys are cast and tested for bare frame and many combinations of URM infill panels. Tri-axial shake table is used for testing. The details of the numerical analysis and experimentation carried out in the research project are brought out in this paper.Item Significance of modeling techniques in pushover analysis of RC buildings(2010) Thapa, M.; BabuNarayan, K.S.; Halemane, K.P.; Venkataramana, K.; Yaragal, S.C.; Ramesh Babu, R.; Sharma, A.; Reddy, G.R.The study presented here focuses on the effectiveness of the models adopted for the nonlinear static pushover (NSP) analysis and providing the best model that can predict the nonlinear response of RC buildings with sufficient accuracy with respect to the experimentally obtained results. NSP analysis considers material nonlinearity and is an effective tool to evaluate the performance of the structure under lateral seismic loads. However, the actual test data in order to verify the results of NSP analysis are very rare for RC structures, which are analytically sensitive to the models and procedure adopted by the analyzer. Under the present work three cases of geometric models; a) Frame with beamcolumn elements, b) Frame with beam-column elements and slabs modelled as a rigid diaphragm and c) Frame with beam-column elements and slabs modelled as shell element considering concrete as confined and unconfined were analyzed. Comparision of analytical curve with the experimental pushover curve, clearly suggests that frame modelled as confined beam-column elements and slabs modelled as a rigid diaphragm gives closer results. © 2010 CAFET-INNOVA TECHNICAL SOCIETY. All rights reserved.Item Studies on concrete cylinders subjected to elevated temperatures(2010) Babu Narayan, K.S.; Anil Kumar, G.; Chandrakala, C.; Shashikumar, H.M.; Venkataramana, K.; Yaragal, S.C.; Chinnagiri Gowda, H.C.; Reddy, G.R.; Sharma, A.Concrete is a poor conductor of heat, but can suffer considerable damage when exposed to fire. Concrete in structures is likely to be exposed to high temperatures during fire. The relative properties of concrete after such an exposure are of great importance in terms of the serviceability of buildings. Unraveling the heating history of concrete is important to forensic research or to determine whether a fire exposed concrete structures and its components are still structurally sound or not. Assessment of fire damage concrete structures usually starts with visual observation of color change, cracking and spalling. On heating, a change in color from normal to pink is often observed and this is useful since it coincides with the onset of significant loss of concrete strength. This work reports the characteristics of concrete at elevated temperatures. Popular normal strength grades (M20, M25, M30, M35, M40 and M45) produced by Ready Mix Concrete (RMC) India, Mangalore have been used in production of test specimens (150 mm diameter and 300mm height cylinders) to obtain more meaningful and realistic data. In the preliminary phase 150 mm diameter and 300mm height cylinders were cast, cured and tested by destructive method for gathering data on strength characteristics. Later these test samples were subjected to elevated temperatures ranging from 100°C to 800°C, in steps of 100°C with a retention period of 2 hours. After exposure, weight losses were determined and then again destructive tests were conducted to estimate the residual split tensile strength. Test results indicated that weight and strength significantly reduces with an increase in temperature. © 2010 CAFET-INNOVA TECHNICAL SOCIETY. All rights reserved.Item Strength retention characteristics of concrete cubes subjected to elevated temperatures(2010) Yaragal, S.C.; Clarke, K.S.; Mahesh Babu, K.; Ashokumar, S.; Venkataramana, K.; Babu Narayan, K.S.; Chinnagiri Gowda, H.C.; Reddy, G.R.; Sharma, A.Concrete in structures is likely to be exposed to high temperatures during fire. The relative properties of concrete after such an exposure are of great importance in terms of the serviceability of buildings. The probability of its exposure to elevated temperatures is high due to natural hazards, accidents and sabotages. Therefore, the performance of concrete during and after exposure to elevated temperature is a subject of great interest to the designer. Physical changes like cracking, colour change, spalling and chemical changes like decomposition of Ca(OH)2 and the C-S-H gel take place when subjected to elevated temperatures. This work reports the characteristics of concrete at elevated temperatures. Popular normal strength grades (M20, M25, M30, M35, M40 and M45) produced by Ready Mix Concrete (RMC) India, Mangalore have been used in production of test specimens (150 mm cubes) to obtain more meaningful and realistic data. In the preliminary phase 150 mm cubes were cast, cured and tested by destructive method for gathering data on strength characteristics. Later these test samples were subjected to elevated temperatures ranging from 100°C to 800°C, in steps of 100°C with a retention period of 2 hours. After exposure, weight losses were determined and then again destructive tests were conducted to estimate the residual compressive strength. Test results indicated that weight and strength significantly reduces with an increase in temperature. © 2010 CAFET-INNOVA TECHNICAL SOCIETY.Item Studies on normal strength concrete cubes subjected to elevated temperatures(2010) Yaragal, S.C.; Babu Narayan, K.S.; Venkataramana, K.; Kulkarni, K.S.; Gowda, H.C.C.; Reddy, G.R.; Sharma, A.Concrete in structures is likely to be exposed to high temperatures during fire. The probability of its exposure to elevated temperatures is high due to natural hazards, accidents and sabotages. Therefore, the performance of concrete during and after exposure to elevated temperature is a subject of great importance and interest to the designer. Popular normal strength grades of concrete produced by Ready Mix Concrete (RMC) India, Mangalore have been used in production of test specimens (150 mm cubes), cured and tested by destructive method for gathering data on strength characteristics. Later, these test samples were subjected to elevated temperatures ranging from 100 C to 800 C, in steps of 100 C with a retention period of 2 hours. After exposure, weight losses and the residual compressive strength retention characteristics are studied. Test results indicated that weight and strength significantly reduces with an increase in temperature. Residual compressive strength prediction equations are proposed for normal strength concretes subjected to elevated temperatures.Item Studies on the influence of infill on dynamic characteristics of reinforced concrete frames(CAFET INNOVA Technical Society 1-2-18/103, Mohini Mansion, Gagan Mahal Road, Domalguda, Hyderabad 500029, 2011) Chethan, K.; Ramesh Babu, R.; Venkataramana, K.; Sharma, A.The basic investigation under dynamic loads starts with the estimation of the natural frequencies of the structure or system under consideration. This is an important parameter under dynamic analysis. Hence a detailed study has been carried out on the influence of masonry infill (MI) on fundamental natural frequency of RC frames. MI though considered as non-structural element largely affect the strength, stiffness and ductility of the framed structure during the application of lateral forces such as wind and earthquake loads. Experimental and Numerical studies are carried out on RC frames under different configurations of MI in addition to bare frames. The RC frames are designed and detailed as per the relevant Indian standard codes. A simple numerical method has been formulated to obtain the natural frequencies of RC frames with MI using FE analysis. Tri-axial shake table is used for the determination of natural frequencies experimentally. This is a part of the collaborative project between BARC, Mumbai and CPRI, Bangalore focusing on the Response evaluation of RC frames under dynamic loading. This paper consists of numerical formulation, FE analysis, Shake table tests and comparison of results. © 2011 CAFET-INNOVA TECHNICAL SOCIETY. All rights reserved.Item Performance appraisal of RC beams using welded wire fabrics as lateral reinforcement in seismic zones(CAFET INNOVA Technical Society 1-2-18/103, Mohini Mansion, Gagan Mahal Road, Domalguda, Hyderabad 500029, 2011) Gowda, H.C.C.; Babu Narayan, K.S.; Venkataramana, K.Ductility is the key to design earthquake resistant structures. More rigid the structure or the element, more it attracts inertia forces. Structures and elements of infinite rigidity are out of question. Codes of practice also advocate design philosophies wherein effects of small earthquakes are to be absorbed with little or no damage, medium with damage to such extents that rehabilitation is possible and large earthquake effects to be catered without collapse. To absorb the tremendous energies that are input to structures and elements unless ductility is ensured, performance levels proposed by codes and standard practices cannot be attained. Lateral ties hold longitudinal reinforcement of R.C.elements in place and also confine the concrete. The basis of the present work is the usage of welded wire fabrics as lateral reinforcement in RC beams. A series of beams were tested with lateral ties and welded wire fabric at discrete locations and welded wire fabric alone throughout the beam with different mesh opening sizes. This paper presents the encouraging results with marginal increase in strength and considerable improvement in ductility in addition to reduced crack widths as observed for specimens having welded wire fabric with smaller mesh openings as lateral reinforcement by confining concrete. © 2011 CAFET-INNOVA TECHNICAL SOCIETY. All rights reserved.Item Characteristics of normal strength concrete with and without chemical admixtures at elevated temperatures(CAFET INNOVA Technical Society 1-2-18/103, Mohini Mansion, Gagan Mahal Road, Domalguda, Hyderabad 500029, 2011) Yaragal, S.C.; Warad, S.A.; Babu Narayan, K.S.; Venkataramana, K.Fire is one of the most destructive powers to which a building structure can be subjected. Behavior of concrete when exposed to fire in cases like nuclear plants, cooling towers or any accidental fire in industrial buildings, is a serious concern, on the strength retention property of concrete. This work reports strength retention studies on compressive and split tensile strength of normal concrete with and without the chemical admixture (Reobuild 918, BASF make) at elevated temperatures. Concrete cubes of size 100 mm have been cast as per prior mix design for M30 grade of concrete, 28 days water cured and tested by destructive method for strength before exposure. Later these specimen were subjected to elevated temperatures of 200°C, 400°C, 600°C and 800°C with a retention period of 2 hours and were allowed cool within the furnace to reach ambient temperature. Later their appearance, colour and cracks were observed and also weight losses were determined. Further, destructive tests were conducted to estimate residual compressive and residual split tensile strengths and prediction equations are proposed to ascertain splitting tensile strengths from compressive strengths. © 2011 CAFET-INNOVA TECHNICAL SOCIETY. All rights reserved.