Journal Articles
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/19884
Browse
3 results
Search Results
Item Tracing of Ammonia Gas by Solution-Combustion-Derived Pristine and Nb-Doped TiO2 Films: Beneficial Impact of Crystallinity and Adsorbed Oxygen on the Gas Response(Springer, 2023) Vardhan, R.V.; Manjunath, G.; Pothukanuri, P.; Mandal, S.The current work delivers room-temperature ammonia (NH3) gas-detectable pristine, Nb-doped TiO2 air- and vacuum-annealed films obtained through the solution-combustion process. Polycrystalline anatase crystal structured films without any dopant oxide phases were processed at 400°C on glass substrates. The crystallinity was higher in pristine films than in doped films; the morphological features were similar in all the films. The films were > 50% transparent, and the estimated optical energy band gap was greater in doped films than in pristine films. All the films detected NH3 gas (25 ppm to 100 ppm) at room temperature, and the gas response was highly dependent on the crystallinity and relative area fraction of adsorbed oxygen (% of OA). The vacuum-annealed pristine film exhibited a better gas response than the other films at all NH3 gas concentrations due to high crystallinity and % of OA (10.15%). The film demonstrated maximum gas response of ~16 towards 100 ppm of NH3 gas and displayed good selectivity. Even though the doping reduced the crystallite size from ~17 nm to ~9 nm, it also diminished the crystallinity of the films, which significantly impacted the deterioration of their gas response. © 2023, The Minerals, Metals & Materials Society.Item Detection of ethanol gas at room temperature by In2O3-based screen-printed films fabricated through particle-free aqueous solution combustible inks(Institute of Physics, 2024) Vardhan, R.V.; Praveen, L.L.; Manjunath, G.; Pothukanuri, P.; Seikh, A.H.; Alnaser, I.A.; Mandal, S.The current work investigates the room temperature ethanol gas detection capabilities of pristine, Sn-doped, Zn-doped, Sn & Zn co-doped In2O3-based screen-printed films, fabricated using particle-free aqueous solution combustible inks on glass substrates. The fabricated films were pure, polycrystalline with cubic bixbyite crystal structure, porous, and transparent (∼75 to 95%) in the visible range. Relatively high surface roughness was detected in pristine film than in doped films. Ethanol gas was detected by all the films at room temperature. Among all, the pristine film showed a relatively greater gas response at all concentrations of ethanol gas ranging from 25 ppm to 100 ppm. This superior gas response was attributed to comparatively greater oxygen vacancy concentration (OV/OL), relative area fraction of surface adsorbed oxygen (% of OA), and high surface roughness with porosity. The maximum ethanol gas response attained was ∼17 at 100 ppm concentration by the pristine film, which also demonstrated high selectivity to ethanol gas. © 2024 The Author(s). Published by IOP Publishing Ltd.Item All-printed WO3 films on an Ag-interdigitated electrode derived from aqueous screen-printable inks for room-temperature ammonia gas detection(Institute of Physics, 2025) Praveen, L.L.; Singh, N.P.; Vardhan, R.V.; Mandal, S.In this work, all-printed tungsten oxide (WO3) sensors were fabricated from nanoparticle-based screen-printable inks, where the WO3 nanopowders were hydrothermally synthesized with various HCl concentrations to give enhanced room-temperature detection of ammonia (NH3) gas. The monoclinic phase of WC powders (calcined WO3) with square nanoplate-like morphology and porosities was identified from x-ray diffraction, field-emission scanning electron microscopy and Brunauer-Emmett-Teller surface area analysis. The silver precursor ink-derived interdigitated electrodes were found to be crystalline with an average finger width and Ag film thickness of 1 ± 0.4 mm and 3.8 ± 0.5 µm, respectively. The formulated WO3 inks with hydroxyethyl cellulose showed a thixotropic fluid-like behavior and exhibited a viscosity of ?9 × 104 mPa s, which is a key requirement for screen printing. Rheological study of the formulated WC inks revealed a thixotropic nature, with all WC inks showing a viscosity of 85 ± 3 Pa s and a recovery rate of 80% in the recovery stage. This work explains the role of pH in hydrothermally synthesis of WO3 by correlating the gas-sensing characteristics of the screen-printed sensors fabricated from formulated inks, where the WC-15 gas sensor showed a maximum gas response of ?340 towards 100 ppm of NH3 gas. This facile and cost-effective method for fabricating chemiresistive gas sensors could pave the way for the development of flexible and printable devices for ppb-level detection of NH3 gas and its monitoring. © 2025 IOP Publishing Ltd. All rights, including for text and data mining, AI training, and similar technologies, are reserved.