Journal Articles
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/19884
Browse
6 results
Search Results
Item Microstructure Evolution in Cast Al-Zn-Mg Alloys Processed by Equal Channel Angular Pressing(Springer New York LLC barbara.b.bertram@gsk.com, 2018) Manjunath, G.K.; Udaya Bhat, K.; Preetham Kumar, G.V.In the present work, microstructure development and enhancement in the microhardness of Al-Zn-Mg alloys (with 5, 10, and 15% zinc) during equal channel angular pressing (ECAP) were investigated. Dendritic morphology was observed in the cast condition of all three alloys, and precipitates were situated along the inter-dendritic regions. After homogenization, precipitates in the inter-dendritic regions were uniformly distributed in the aluminum matrix and grain boundaries were developed. After 4 passes in route BC, large reduction in the grain size was observed. X-ray diffractometry showed that MgZn2 precipitate was developed in the ECAP-processed samples. Increase in the intensity of MgZn2 peaks was observed when the quantity of zinc is increased in the material. Also, changes in the intensity of XRD peaks were observed in ECAP-processed samples due to shear deformation. After ECAP, substantial increase in the microhardness was perceived. After four passes, microhardness increased to 109, 67, and 58% from the initial condition in A1, A2, and A3 alloys, respectively. Also, improvement in the microhardness was also observed when the quantity of zinc is increased in the material. © 2017, Springer Science+Business Media, LLC, part of Springer Nature and ASM International.Item Effect of zinc content on the microstructure and mechanical properties of Al-Zn-Mg alloy(Elsevier Ltd, 2022) Manjunath, G.K.; Udaya Bhat, K.; Preetham Kumar, G.V.In the present work, Aluminium-Zinc-Magnesium alloys (5 wt%, 10 wt% and 15 wt% Zinc and 2 wt% Magnesium) were prepared by casting process in a metal die. After casting process, heat treatment was conducted to the prepared alloys. To study the consequence of Zinc on the prepared alloys microstructure and mechanical properties were investigated. In as-cast state, in all three compositions, dendrite formation was noticed. While, after homogenization heat treatment, grain boundaries were noticed. Rise in the Zinc in the material leads to enhance the secondary particles. Microhardness and tension experiments were conducted to investigate the mechanical properties. Rise in the Zinc in the material leads to enhance the microhardness and tension strength. But ductility of the material declined with rise in the Zinc in the material. © 2021Item Enhancing the surface integrity characteristics of Al-Li alloy using face milling(Elsevier B.V., 2022) Marakini, V.; Srinivasa Pai, P.; Udaya Bhat, K.; Thakur, D.S.; Achar, B.P.This work presents the milling induced surface integrity investigation of Al-Li alloy. The effect of milling on the surface roughness, microhardness, microstructure, and residual stress is studied. Uncoated carbide inserts are used for milling due their superior hardness and greater life, when machining softer materials such as aluminium and its alloys. Results show that the minimum surface roughness (Ra = 0.043 µm) and maximum microhardness (216 HV) are achievable from the milling process, when compared with the roughness (Ra = 0.528 µm) and microhardness (180 HV) of the as-received material. Results indicate limited harm to alloy microstructure from the milling process and the presence of compressive residual stress induced from milling. The work finds scope for aerospace applications. © 2022 Elsevier B.V.Item Microstructural Features Intimated in Automotive Grade IF Steel Subjected to Conventional and Severe Shot Peening(Springer, 2024) Sahoo, B.; Udaya Bhat, K.A significant amount of interstitial-free or IF steel is used to manufacture automotive body parts due to its high ductility, high formability, and low yield strength. But, the major drawback of this steel is the lower surface hardness. The current investigation intended to enhance the surface hardness by employing shot peening at different coverages. The work also studied the microstructural features intimated after the treatment and its effect on the surface hardness. The optical and transmission electron microscopy (TEM) results showed a prominent grain refinement and dislocation hardening, which improved the micro-hardness to 2.5 times. Tri-junctions, sub-grains, twins, nanocrystalline regions, and several dislocation-induced microstructural features, like dislocation bands, dislocation forests, dislocation walls, dislocation cell structure, etc., were detected in the samples after peening. These features bear a beneficial impact on the surface hardness of the substrate. A spatial filter (Sobel filter) was used to refine the image and detect the presence of NbC precipitates near the grain boundary. Using Gatan DigitalMicrograph software, the thermal imaging technique effectively identified thinner grain boundaries near the segregation zone. © ASM International 2024.Item Tailoring the surface characteristics and mechanical behavior of Ti-Nb stabilized IF steel through controlled shot peening coverage(Elsevier Ltd, 2025) Sahoo, B.; Udaya Bhat, K.; Kumar, D.S.The rising demand for a qualitative surface opens a new window of research in the domain of mechanical surface treatment, known as severe shot peening, especially in the automotive industry. The effectiveness of this method is usually affiliated with various process parameters, of which peening coverage is the most sought-after. It is anticipated to elevate the surface characteristics by proficiently optimizing the peening coverage. On this ground, the current investigation tries to gather the beneficial effect of peening coverage on the surface properties of Ti-Nb stabilized interstitial-free steel subjected to severe shot peening by considering four different coverages (100 %, 500 %, 1000 %, and 2000 %). The work attempts to interpret the impact of peening coverage on grain refinement and dislocation-induced microstructures at different depths of the as-treated sample. The crossectional microscopy unveiled a prominent grain refinement hardening and dislocation hardening in 2000 % peening coverage up to a depth of 90–120 µm, firmly agreeing with the microhardness depth profile. The optical microscopy identified four zones of deformation (severe deformation, deformation, transition, and undeformed zone) in the sample treated with the highest coverage. The transmission electron microscopy demonstrated the dominance of certain dislocation-derived features like dislocation forest, dislocation cells, tangled dislocations, dislocation bands, nanocrystalline region, stress concentration region, etc., at the deformed zone of the treated samples. Interestingly, the trace of these features was detected at a greater depth for the highest-peened sample than the lowest-peened sample, affirming the beneficial aspect of higher peening coverage. The stored energy and thermal stability assessment in the as-received and as-treated sample was done in the differential scanning calorimeter, revealing the favorable impact of severe peening on the substrate. The surface topographical study in a 3D profilometer also unveils the variation in the surface roughness and functional volume parameters. The present investigation also analyzed the maximum depth and mean density of furrows to verify the severe plastic deformation in the as-treated sample. © 2024Item Enhancement of Microstructural, Mechanical, and Tribological Properties of AA5083 Alloy via Multi-axial Forging(Springer, 2025) Aravindh, G.; Sahoo, B.; Kumar, G.V.P.; Udaya Bhat, K.The present study investigates the influence of multi-axial forging (MAF) on the microstructure, mechanical, and wear properties of the AA5083 alloy. After solution treatment, the alloy was subjected to three MAF cycles at room temperature with a strain of 0.63 per cycle. The evolution of the microstructure was analyzed using optical microscopy, field emission gun scanning electron microscopy, and x-ray diffraction. Mechanical properties were evaluated through tensile testing, and Vicker’s micro-hardness and wear behavior of the alloys were investigated using reciprocating wear tests. The results demonstrated significant improvement in properties after the third MAF cycle, forming 8.3 ?m wide shear bands and a refined grain structure. The alloy achieved maximum hardness (130 HV), tensile strength (334 MPa), and elongation to failure (8.01%), along with a reduced strain-hardening exponent (0.27). Wear resistance showed marked enhancement, with wear volume reductions of 36%, 49%, and 21% under 1, 2, and 4 N loads, respectively. Similarly, wear rates decreased by 64%, 49%, and 15% under the same loads. These findings emphasize the MAF process's effectiveness in enhancing the mechanical and wear properties of AA5083 alloy, indicating its potential for advanced material processing techniques. © ASM International 2025.