Journal Articles
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/19884
Browse
16 results
Search Results
Item [No abstract available](Springer Netherlands, Low cycle fatigue behavior of an (? + ?) titanium alloy) Nanjundaswamy, G.S.; Ramachandra, C.; Sengupta, P.K.; Chatterji, B.; Sudhakara Nayak, H.V.; Singh, A.K.1998Item Microstructure and corrosion behavior of laser processed NiTi alloy(Elsevier Ltd, 2015) Marattukalam, J.J.; Singh, A.K.; Datta, S.; Das, M.; Balla, V.K.; Bontha, S.; Kalpathy, S.K.Abstract Laser Engineered Net Shaping (LENS™), a commercially available additive manufacturing technology, has been used to fabricate dense equiatomic NiTi alloy components. The primary aim of this work is to study the effect of laser power and scan speed on microstructure, phase constituents, hardness and corrosion behavior of laser processed NiTi alloy. The results showed retention of large amount of high-temperature austenite phase at room temperature due to high cooling rates associated with laser processing. The high amount of austenite in these samples increased the hardness. The grain size and corrosion resistance were found to increase with laser power. The surface energy of NiTi alloy, calculated using contact angles, decreased from 61 mN/m to 56 mN/m with increase in laser energy density from 20 J/mm2 to 80 J/mm2. The decrease in surface energy shifted the corrosion potentials to nobler direction and decreased the corrosion current. Under present experimental conditions the laser power found to have strong influence on microstructure, phase constituents and corrosion resistance of NiTi alloy. © 2015 Elsevier B.V.Item Quasi-Static and High Strain Rate Compressive Response of Injection-Molded Cenosphere/HDPE Syntactic Foam(Minerals, Metals and Materials Society 184 Thorn Hill Road Warrendale PA 15086, 2016) Bharath Kumar, B.R.; Singh, A.K.; Doddamani, M.R.; Luong, D.D.; Gupta, N.High strain rate compressive properties of high-density polyethylene (HDPE) matrix syntactic foams containing cenosphere filler are investigated. Thermoplastic matrix syntactic foams have not been studied extensively for high strain rate deformation response despite interest in them for lightweight underwater vehicle structures and consumer products. Quasi-static compression tests are conducted at 10?4 s?1, 10?3 s?1 and 10?2 s?1 strain rates. Further, a split-Hopkinson pressure bar is utilized for characterizing syntactic foams for high strain rate compression. The compressive strength of syntactic foams is higher than that of HDPE resin at the same strain rate. Yield strength shows an increasing trend with strain rate. The average yield strength values at high strain rates are almost twice the values obtained at 10?4 s?1 for HDPE resin and syntactic foams. Theoretical models are used to estimate the effectiveness of cenospheres in reinforcing syntactic foams. © 2016, The Minerals, Metals & Materials Society.Item Development of glass microballoon/HDPE syntactic foams by compression molding(Elsevier Ltd, 2017) Jayavardhan, M.L.; Bharath Kumar, B.R.; Doddamani, M.; Singh, A.K.; Zeltmann, S.E.; Gupta, N.Thermoplastic resins are widely used in consumer products and industrial components. There is a significant interest in weight reduction of many of those components. Although glass hollow particle filled lightweight syntactic foams with thermoset matrices have been studied in detail, studies on thermoplastic syntactic foams are scarce. The present study is focused on developing a compression molding based processing method for glass microballoon/high density polyethylene (GMB/HDPE) syntactic foams and studying their mechanical properties to develop structure-property correlations. Blending of GMB in HDPE is carried out using a Brabender mixer with processing parameters optimized for minimal filler breakage. Flexural and tensile test specimens are compression molded with 20, 40 and 60 vol% of GMB. Particle fracture increases with increasing GMB content due to increased particle to particle interaction during processing. Additionally, increasing wall thickness makes GMBs stronger and results in reduced particle fracture. Flexural modulus increases while strength decreases with increasing filler content. Tensile strength decreases with increasing filler content, while tensile modulus is relatively unchanged. GMB volume fraction has a more prominent effect than the wall thickness on the mechanical properties of syntactic foams. Specific moduli of GMB/HDPE foams are superior while specific strength is comparable to neat HDPE. © 2017 Elsevier LtdItem Additive Manufacturing of Syntactic Foams: Part 2: Specimen Printing and Mechanical Property Characterization(Minerals, Metals and Materials Society 184 Thorn Hill Road Warrendale PA 15086, 2018) Singh, A.K.; Saltonstall, B.; Patil, B.; Hoffmann, N.; Doddamani, M.; Gupta, N.High-density polyethylene (HDPE) and its fly ash cenosphere-filled syntactic foam filaments have been recently developed. These filaments are used for three-dimensional (3D) printing using a commercial printer. The developed syntactic foam filament (HDPE40) contains 40 wt.% cenospheres in the HDPE matrix. Printing parameters for HDPE and HDPE40 were optimized for use in widely available commercial printers, and specimens were three-dimensionally (3D) printed for tensile testing at strain rate of 10?3 s?1. Process optimization resulted in smooth operation of the 3D printer without nozzle clogging or cenosphere fracture during the printing process. Characterization results revealed that the tensile modulus values of 3D-printed HDPE and HDPE40 specimens were higher than those of injection-molded specimens, while the tensile strength was comparable, but the fracture strain and density were lower. © 2018, The Minerals, Metals & Materials Society.Item Additive Manufacturing of Syntactic Foams: Part 1: Development, Properties, and Recycling Potential of Filaments(Minerals, Metals and Materials Society 184 Thorn Hill Road Warrendale PA 15086, 2018) Singh, A.K.; Patil, B.; Hoffmann, N.; Saltonstall, B.; Doddamani, M.; Gupta, N.This work focuses on developing filaments of high-density polyethylene (HDPE) and their hollow particle-filled syntactic foams for commercial three-dimensional (3D) printers based on fused filament fabrication technology. Hollow fly-ash cenospheres were blended by 40 wt.% in a HDPE matrix to produce syntactic foam (HDPE40) filaments. Further, the recycling potential was studied by pelletizing the filaments again to extrude twice (2×) and three times (3×). The filaments were tensile tested at 10?4 s?1, 10?3 s?1, and 10?2 s?1 strain rates. HDPE40 filaments show an increasing trend in modulus and strength with the strain rate. Higher density and modulus were noticed for 2× filaments compared to 1× filaments because of the crushing of some cenospheres in the extrusion cycle. However, 2× and 3× filament densities are nearly the same, showing potential for recycling them. The filaments show better properties than the same materials processed by conventional injection molding. Micro-CT scans show a uniform dispersion of cenospheres in all filaments. © 2018, The Minerals, Metals & Materials Society.Item Additive Manufacturing of Three-Phase Syntactic Foams Containing Glass Microballoons and Air Pores(Minerals, Metals and Materials Society 184 Thorn Hill Road Warrendale PA 15086, 2019) Singh, A.K.; Deptula, A.J.; Anawal, R.; Doddamani, M.; Gupta, N.High-density polyethylene and its syntactic foams reinforced with 20 vol.% and 40 vol.% glass microballoons were 3D printed using the fused filament fabrication method and studied for their compressive response. The three-phase microstructure of syntactic foams fabricated in this work also contained about 10 vol.% matrix porosity for obtaining light weight for buoyancy applications. Filaments for 3D printing were developed using a single screw filament extruder and printed on a commercial 3D printer using settings optimized in this work. Three-dimensional printed blanks were machined to obtain specimens that were tested at 10 ?4 s ?1 , 10 ?3 s ?1 , 10 ?2 s ?1 and 1 s ?1 strain rates. The compression results were compared with those of compression-molded (CM) specimens of the same materials. It was observed that the syntactic foam had a three-phase microstructure: matrix, microballoons and air voids. The air voids made the resulting foam lighter than the CM specimen. The moduli of the 3D-printed specimen were higher than those of the CM specimens at all strain rates. Yield strength was observed to be higher for CM samples than 3D-printed ones. © 2019, The Minerals, Metals & Materials Society.Item Experimental analysis of Android malware detection based on combinations of permissions and API-calls(Springer-Verlag France 22, Rue de Palestro Paris 75002, 2019) Singh, A.K.; Jaidhar, C.D.; M.a, M.A.A.Android-based smartphones are gaining popularity, due to its cost efficiency and various applications. These smartphones provide the full experience of a computing device to its user, and usually ends up being used as a personal computer. Since the Android operating system is open-source software, many contributors are adding to its development to make the interface more attractive and tweaking the performance. In order to gain more popularity, many refined versions are being offered to customers, whose feedback will enable it to be made even more powerful and user-friendly. However, this has attracted many malicious code-writers to gain anonymous access to the user’s private data. Moreover, the malware causes an increase of resource consumption. To prevent this, various techniques are currently being used that include static analysis-based detection and dynamic analysis-based detection. But, due to the enhancement in Android malware code-writing techniques, some of these techniques are getting overwhelmed. Therefore, there is a need for an effective Android malware detection approach for which experimental studies were conducted in the present work using the static features of the Android applications such as Standard Permissions with Application Programming Interface (API) calls, Non-standard Permissions with API-calls, API-calls with Standard and Nonstandard Permissions. To select the prominent features, Feature Selection Techniques (FSTs) such as the BI-Normal Separation (BNS), Mutual Information (MI), Relevancy Score (RS), and the Kullback-Leibler (KL) were employed and their effectiveness was measured using the Linear-Support Vector Machine (L-SVM) classifier. It was observed that this classifier achieved Android malware detection accuracy of 99.6% for the combined features as recommended by the BI-Normal Separation FST. © 2019, Springer-Verlag France SAS, part of Springer Nature.Item Performance of magnetorheological elastomer based torsional vibration isolation system for dynamic loading conditions; ??????????????????????????(Central South University of Technology f-ysxb@mail.csut.edu.cn, 2020) Shenoy, S.K.; Kuchibhatla, S.A.R.; Singh, A.K.; Gangadharan, K.V.Vibration isolation is an effective method to mitigate unwanted disturbances arising from dynamic loading conditions. With smart materials as suitable substitutes, the conventional passive isolators have attained attributes of semi-active as well as the active control system. In the present study, the non-homogenous field-dependent isolation capabilities of the magnetorheological elastomer are explored under torsional vibrations. Torsional natural frequency was measured using the serial arrangement of accelerometers. Novel methods are introduced to evaluate the torsional stiffness variations of the isolator for a semi-definite and a motor-coupled rotor system. For the semi-definite system, the isolation effect was studied using the frequency response functions from the modal analysis. The speed-dependent variations for motor-coupled rotor system were assessed using the shift in frequency amplitudes from torque transducers. Finite element method magnetics was used to study the variations in the non-homogenous magnetic field across the elastomer. The response functions for the semi-definite rotor system reveal a shift in the frequency in the effect of the magnetic field. Speed-dependent variations in the frequency domain indicate an increment of 9% in the resonant frequency of the system. © 2020, Central South University Press and Springer-Verlag GmbH Germany, part of Springer Nature.Item In silico structural and functional analysis of bacillus uricases(Bentham Science Publishers, 2021) Nelapati, A.K.; Meena, S.; Singh, A.K.; Bhakta, N.; JagadeeshBabu, P.E.Background: Excluding humans, the peroxisomal uricase is responsible for the catabolism of uric acid into allantoin in many species like microorganisms, plants, and inverte-brates. Particularly in humans, the synthesis and excretion of uric acid are naturally balanced. When the uric acid concentration crosses 7 mg/dl, it results in conditions such as hyperuricemia and gout. Uricase is one of the potential sources for the reduction of uric acid in humans. Uricase is also widely used as a commercial diagnostic reagent in medical and clinical biochemistry to esti-mate the uric acid concentration in blood and other biological fluids. Computational approaches can be used for screening and investigation of uricase enzyme with desirable characteristics that can be employed in diverse industrial applications. Objectives: The present study deals with computational-based structural, functional, and phylogenetic analyses of uricase enzymes from various Bacillus species. Methods: Seventy uricase protein sequences from Bacillus species were selected for multiple sequence alignment, phylogenetic analysis, motif assessment, domain architecture examination, understanding of basic physicochemical properties and in silico identification of the composition of amino acids in uricase. Further, structural (secondary and tertiary structure prediction), and functional (CYS_REC, MOTIF scan, CD-search, STRING, SOSUI, and PeptideCutter) analyses of uric-ase were performed. Results: Bacillus simplex (WP_063232385.1) was chosen as the representative species of the Bacillus genera. The three-dimensional (3D) structure of B. simplex uricase was predicted and validated using QMEAN, RAMPAGE, ERRAT, Verify 3D and PROQ servers. The analysis revealed that the tertiary structure of the selected uricase has good quality and acceptability. Conclusion: Computational analysis of uricase from various Bacillus sources revealed that all the selected Bacillus uricases are active within acidic to a neutral environment, and thermally stable with a molecular weight ranging from 35.59-59.85kDa. The secondary structure analysis showed that all uricases are rich in alpha-helices and sheets. The CDD tool identified two conserved do-mains, one of which belongs to OHCU decarboxylase and another belongs to Uricase superfamily. The quality estimation of 3D modeled protein gave a high overall quality factor score of 94.64. Al-so, all Bacillus species of uricase enzyme and their corresponding genes showed a strong correlation from the phylogenetic comparison of the selected taxa. The present detailed computational investigation on the uricase protein could help in screening a suitable uricase producing microbe with desirable characteristics for industrial application. © 2021 Bentham Science Publishers.