Journal Articles
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/19884
Browse
5 results
Search Results
Item A comparative study on a newly designed ball mill and the conventional ball mill performance with respect to the particle size distribution and recirculating load at the discharge end(Elsevier Ltd, 2020) Hanumanthappa, H.; Vardhan, H.; Raj, G.R.; Kaza, M.; Sah, R.; Shanmugam, B.K.The discharge end design of a ball mill plays an important role in discharging the desired particle sizes (?150 + 10 µm) and the percentage of recirculating load from the discharge end of the ball mill. In continuous wet ball mills, the composition of feed (hard ore or soft ore) to the mill varies continuously, leading to uncontrolled grinding in the mill. In view of this, a new design of the discharge mechanism has been implemented to remove the ground particles of desired particle size fraction with minimum recirculating load (+150 µm). The results from the discharge end with lifters (closed and open) show that the particle size fraction obtained from the discharge end has a maximum percentage of desired particle size fraction when the mill is operating at 60% critical speed. Discharge end without lifters has an uncontrolled particle size distribution in the discharge and the percentage of desired-size particles discharged was found to be very less. Also, the percentage of the recirculating load is minimum in the case of discharge end with lifter design compared with discharge end without a lifter. Hence, a new design of lifters in the discharge end leads to the discharge of the desired particle size fraction with minimum recirculating load. © 2019 Elsevier LtdItem Estimation of Grinding Time for Desired Particle Size Distribution and for Hematite Liberation Based on Ore Retention Time in the Mill(Springer, 2020) Hanumanthappa, H.; Vardhan, H.; Raj, G.R.; Kaza, M.; Sah, R.; Shanmugam, B.K.Iron ores obtained from different sources differ in their chemical and physical properties. These variations make the process of grinding a difficult task. The work carried out in this context focuses on three different samples of iron ore, viz., high silica high alumina, low silica high alumina, and low silica low alumina. The grinding process for all the three iron ores is carried out individually in Bond’s ball mill and the total retention time taken by each iron ore sample is calculated. The present investigation focuses on utilizing the calculated retention time of the iron ore as a standard grinding reference time to the laboratory ball mill for optimizing the grinding time of each ore. The desired P80 (150 ?m) with an acceptable range of hematite liberation (> 75%) was obtained in the laboratory ball mill after reducing 6 min from the total retention time taken in the Bond ball mill. © 2020, Society for Mining, Metallurgy & Exploration Inc.Item Evaluation of a new vibrating screen for dry screening fine coal with different moisture contents(Routledge, 2022) Shanmugam, B.K.; Vardhan, H.; Raj, M.G.; Kaza, M.; Sah, R.; Hanumanthappa, H.A new vibrating screen was developed with a circular mode of vibration for dry screening of moist coal of size fraction ?3 + 1 mm. Screen mesh of 2 mm aperture size will be used to separate the finer coal particles of size fraction ?2 + 1 mm. The new vibrating screen has the flexibility in changing the operational parameters such as the angle of the screen in upward or downward sloping direction and frequency of vibration of the screen deck. The circular mode of vibration provided to the screen deck will incorporate the inertial force on the particle in the screen deck, reducing screen clogging. The present study involves the analysis of the screening performance of the new vibrating screen with the coal feed of varying moisture content of 4%, 6% and 8%. The maximum screening efficiencies obtained for screening the coal feed with the moisture contents of 4%, 6% and 8% were 85.96%, 77.84%, and 68.27%, respectively. The higher screening performance of new vibrating screen was obtained due to good exposure time, particle mixing, particle segregation and particle stratification of coal on the screen deck. The results of the new vibrating screen will be a breakthrough in dry screening technology and accelerate the pilot-scale development. © 2019 Taylor & Francis Group, LLC.Item ANN modeling and residual analysis on screening efficiency of coal in vibrating screen(Taylor and Francis Ltd., 2022) Shanmugam, B.K.; Vardhan, H.; Raj, M.G.; Kaza, M.; Sah, R.; Hanumanthappa, H.In this paper, coal screening in vibrating screen was carried out with the size ranges of ?6 mm + 4 mm, ?4 mm + 2 mm, and ?2 mm + 0.5 mm. The vibrating screen was newly designed with flexibility in angle and frequency. The vibrating screen experimentation was carried out by varying screen mesh, angle, and screen frequency. During the screening, the angle was kept constant, and frequency was varied to obtain each size range’s screening efficiency. The experimental results of screening efficiency were evaluated for each size fraction range of coal. The maximum efficiency for screening coal with ?6 mm+4 mm, ?4 mm+2 mm, and ?2 mm+0.5 mm size range obtained was 87.60%, 80.93%, and 62.96%, respectively. Further, the prediction model was developed for each size range using a feed-backward artificial neural network (ANN) to consider the back-propagation error technique. For each screening condition, 10 ANN models were developed with the variation in 1–10 different neurons. ANN has provided mathematical models with a 99.9% regression coefficient for predicting each size range’s screening efficiency. Furthermore, the residuals of each optimal ANN model were analyzed using a normal probability plot and histogram. The ANN model’s accuracy was obtained from the residual analysis by evaluating four different model conditions, i.e., independence, homoscedasticity, normality, and mean error. © 2021 Taylor & Francis Group, LLC.Item Experimental analysis of vibratory screener efficiency based on density variation for screening coal and iron ore(Taylor and Francis Ltd., 2024) Shanmugam, B.K.; Vardhan, H.; Raj, M.G.; Kaza, M.; Hanumanthappa, H.; Reddy Byrareddy, R.; Sah, R.In the coal and mineral beneficiation industries, screening is one of the crucial physical separation methods carried out to separate the undersized fine particles from the oversize coarse particles. The vibratory screener is a relatively advanced screening technology applied for coal and iron ore beneficiation. This paper deals with the experimental investigation for assessing the efficiency of screening coal and iron ore in the vibratory screener. Furthermore, a comparative study between the test performance of screening coal and iron ore was carried out depending on moisture and density variation. Test results show that the vibratory screener can provide a high recovery of fines and increased efficiency for screening iron ore than coal material. The maximum efficiency of iron ore was attained at a higher angular position, such as 3 and 5 degrees in an upward slope, whereas the maximum efficiency of coal was attained at 1 degree in an upward slope. © 2023 Taylor & Francis Group, LLC.