Journal Articles
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/19884
Browse
10 results
Search Results
Item Influence of microwave hybrid heating on the sliding wear behaviour of HVOF sprayed CoMoCrSi coating(Institute of Physics Publishing helen.craven@iop.org, 2018) Prasad, C.D.; Joladarashi, S.; Ramesh, M.R.; Srinath, M.S.; Channabasappa, B.H.CoMoCrSi superalloy powder (Tribaloy-T400) consists of intermetallic laves phase and primary eutectic phase of Co-rich solid solution. Processing of Tribaloy-T400 powder is carried out through high-energy ball milling (HEBM) technique to obtain a higher volume fraction of intermetallic laves phases. The feedstock is sprayed using high-velocity-oxy-fuel (HVOF) process on titanium grade-15 substrate. The coating microstructure is homogenized by microwave hybrid heating technique. Characterization of feedstock, as-sprayed and microwave fused coatings is done by using Scanning Electron Microscopy (SEM), Energy dispersive spectroscopy (EDS) and x-ray Diffraction (XRD). Porosity, surface roughness, microhardness, and bond strength are measured. Adhesive wear behavior of the coatings under the dry sliding condition is evaluated at an applied load of l0 and 20 N and temperature of 200, 400 and 600 °C Fused coating exhibit higher wear resistance than the as-sprayed coatings and substrate. The hard intermetallic laves phases which are amorphous (bulk metallic glass) in nature strengthen the coating at high temperatures. © 2018 IOP Publishing Ltd.Item Microstructure and tribological characteristics of APS sprayed NiCrBSi/flyash cenosphere/Cr2O3 and NiCrBSi/flyash cenosphere/Mo composite coatings at elevated temperatures(Institute of Physics Publishing helen.craven@iop.org, 2019) Nagabhushana, N.; Rajanna, S.; Mathapati, M.; Ramesh, M.R.; Koppad, P.G.; Reddy, N.C.In the present investigation NiCrBSi/flyash/Cr2O3 and NiCrBSi/flyash/Mo composite coatings are developed using atmospheric plasma spray technique on superni 76 alloy. Coatings are characterized in terms of microstructure, phase analysis, and microhardness. Tribological properties of the coatings are evaluated using a pin on disc tribometer. Test is conducted under dry sliding conditions at room temperature, 200 °C, 400 °C, and 600 °C respectively. Microstructure and worn surfaces of the coatings are analyzed by utilizing Scanning Electron Microscope (SEM) where in phase analysis is carried out using x-ray diffractometer (XRD). XRD results revealed the presence of ?-Ni as primary phase along with Ni3B, Cr7C3, SiO2 and Al2O3 as minor phases in both the NiCrBSi/flyash/Cr2O3 and NiCrBSi/flyash/Mo coatings. Among the two coatings, Mo composite coating exhibited lower porosity and higher microhardness. The friction coefficient of both the coatings decreased with increasing temperature. The wear rate is found to decrease at lower temperatures but increased at a higher temperature (>400 °C) for Cr2O3 composite coating wherein Friction coefficient is decreased with increase in the temperature for Mo composite coatings. The worn surface analysis conducted revealed abrasive wear at lower temperatures while the transition from abrasive to adhesive is observed at higher temperatures. © 2019 IOP Publishing Ltd.Item Tribological behaviour of monolayer and multilayer Ti-based thin solid films deposited on alloy steel(Institute of Physics Publishing helen.craven@iop.org, 2019) V Badiger, P.V.; Desai, V.; Ramesh, M.R.; Joladarashi, S.; Gourkar, H.The fretting wear and adhesive wear resistance of Ti-based thin solid films deposited on MDN121 steel substrate are evaluated. Plasma-assisted cathodic arc evaporation technique is used to develop the TiC-C monolayer coating and Ti/TiN/TiCN/TiN/TiCN multilayer coatings used in the study. FESEM-EDS, nanoindentation, Raman spectroscopy, optical profiler, and confocal microscope are used to characterise the coatings and wear tracks. Diamond-like carbon is observed in the microstructure of both the coatings. During the fretting analysis, the coefficient of friction (COF) is reduced by 68.49% in the case of the TiC-C monolayer coating and 42.46% in the Ti multilayer coatings as compared to the substrate. The volumetric wear loss of the TiC-C monolayer coating is lower than the multilayer coating. The wear surface morphology reveals the abrasive form of the fretting wear mechanism in both the monolayer and multilayer coatings whereas the galling failure in the substrate. During adhesive wear, the COF is reduced by 71.73% in the monolayer coating and 59.33% in the multilayer coatings compared to the substrate. The monolayer coating exhibits low friction and low wear rate as compared to the multilayer coating. © 2018 IOP Publishing Ltd.Item Effect of microwave heating on microstructure and elevated temperature adhesive wear behavior of HVOF deposited CoMoCrSi-Cr3C2 coating(Elsevier B.V., 2019) Prasad, C.D.; Joladarashi, S.; Ramesh, M.R.; Srinath, M.S.; Channabasappa, B.H.This research reports the improvement of high-temperature sliding wear resistance of a grade 15 titanium alloy protected by an HVOF sprayed CoMoCrSi-Cr3C2 coating. The coatings have been tested in as-sprayed condition and after a post-deposition microwave heating step. The powder feedstock has been manufactured by high energy ball milling. X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM) equipped with the Energy Dispersive Spectroscopy (EDS) methods were used for coatings characterization. Surface roughness, microhardness, adhesion strength, and porosity of coatings were also measured. The wear test was conducted at an applied load of l0 N and 20 N with varying temperatures of 200 °C, 400 °C, and 600 °C under dry sliding conditions. Co3Mo2Si, Co7Mo6, Mo3Si, Co3Mo, and Co2Mo3 were the intermetallic laves phases generated in the CoMoCrSi feedstock during HEBM process. The microwave-fused coating exhibited metallurgical bonding, homogeneous structure, less porosity, and greater hardness as compared to as-sprayed coating. Microwave-treated coating revealed better wear property than an as-sprayed coating. This was mainly due to the intermetallic formation and metallurgical bonding in coatings. The fused coatings exhibit tribo-oxide layers during sliding action which was the main phenomenon of improving the wear resistance of the fused composite coatings. © 2019 Elsevier B.V.Item Tribological performance of wire arc additive manufactured 347 austenitic stainless steel under unlubricated conditions at elevated temperatures(Elsevier Ltd, 2020) Duraisamy, R.; Subramaniyan, S.; Kannan, A.; Siva Shanmugam, N.; Sankaranarayanasamy, K.; Ramesh, M.R.Wire Arc Additive Manufacturing (WAAM) is an effective metal additive manufacturing process. In this research, 347 Austenitic Stainless Steel (ASS) walls were manufactured with ER347 consumable material. The microstructure of the WAAM processed 347 plate is entirely heterogeneous with changing grain morphology along the building direction and this is attributed to the complex cyclic thermal history during WAAM process. The microstructure is composed of columnar, cellular and equiaxed structures at various regions. The hardness decreased gradually from bottom to top along the building direction. The volume fraction of ferrite ranged from 0.5% to 4.2% at various regions and the presence of niobium carbide (NbC) was confirmed. The aim of the current work is to provide an outline of the WAAM processed 347 steel under dry sliding conditions at elevated temperatures. The elevated temperature wear mechanism has mild oxidative wear characteristic due to the formation of tribo-oxides on the wearing and sliding surfaces. However, the average coefficient of friction (COF) is lower for the WAAM processed 347 compared to 347 substrate. In all cases after initial running-in, the wear debris from the wearing and sliding surface forms mechanically mixed composite layer of tribo-oxides (Fe2O3, Fe3O4 and Al2O3). The worn surface at 200 °C presents different wear behavior compared to the samples at 400 °C and 600 °C. The wear at 200 °C is a typical adhesive wear, while the wear at 400?600 °C is mild oxidative wear. The increase in the percentage of Fe3O4 helps to heal the wear surface by forming a mechanically mixed composite layer. The characteristics of mild oxidative wear were elucidated. © 2020 The Society of Manufacturing EngineersItem High temperature erosion performance of NiCrAlY/Cr2O3/YSZ plasma spray coatings(Taylor and Francis Ltd., 2023) Reddy, G.M.S.; Prasad, C.D.; Patil, P.; Shetty, G.; Naresh, N.; Ramesh, M.R.The current investigation's objective was to assess the air jet erosion tester's ability to measure the erosive behaviour of plasma sprayed coatings on titanium-15 alloy. 65% NiCrAlY, 30% Cr2O3, and 5% YSZ make up the coating's chemical composition. A study of microstructure and phases was carried out. Microhardness and adhesive strength have both been measured in this work. With impact angles of 30° and 90° at 300°C, 500°C, and 700°C, Al2O3 erodent was utilised in a solid particle erosion test. An optical profilometer was used to calculate the erosion volume loss. The coating erosion resistance was found to be higher than the substrate sample for the test temperature that was employed, and this was more obvious at higher impact angles and higher temperatures The ductile character of the coating is seen in the contour of the deteriorated coating surface. © 2023 Institute of Materials Finishing Published by Taylor & Francis on behalf of the Institute.Item Effect of Microwave Hybrid Heating on High-Temperature Adhesive Wear Behavior of High-Velocity Oxygen Fuel-Sprayed WC-CrC-Ni and WC-Co/NiCrFeSiB Coatings(Springer, 2023) Medabalimi, S.; Ananthu, M.R.; Gudala, S.; Ramesh, M.R.HVOF-processed coatings are chemically inhomogeneous and are not metallurgically bonded to the substrate. As a result, components coated with HVOF experience considerable material degradation during sliding wear. Microwave hybrid heating (MHH) is a novel surface modification technique for modifying the as-sprayed properties of the coating. Hence, this paper investigates and compares the wear and frictional behavior of HVOF as-sprayed coatings against MHH samples of WC-CrC-Ni and WC-Co/NiCrFeSiB coatings at elevated temperatures. MHH had a significant impact on wear rate and coefficient of friction by optimizing the porosity, integrated oxide phases and intersplat cohesion strength of the coatings. A modified domestic oven was used to perform MHH on HVOF-coated samples for 5 min at 1200 °C. Wear tests were performed using a pin-on-disk tribometer from room temperature to 200, 400, and 600 °C with Al2O3 disk as a counterface. SEM/EDS and XRD were utilized to examine the microstructural characterization of the coatings and substrate. Both the coatings showed higher wear resistance than the substrate at all temperatures. The WC-Co/NiCrFeSiB coating produced an oxide layer on the worn surfaces and integrated WC, CoWO4, and Fe2SiO4 splats, enhancing wear resistance. The MHH WC-CrC-Ni coating formed Cr2O3 and NiWO4 phases on the worn surfaces, increasing the intersplat cohesion strength between matrix and carbide splats, lowering the overall wear rate. After MHH, the wear rate of a substrate and WC-CrC-Ni coating was 3.5 and 1.12 times more at room temperature and 8.07 and 2.92 times more at 600 °C than WC-Co/NiCrFeSiB coating. © 2022, ASM International.Item Elevated temperature wear and friction performance of WC-CoCr/Mo and WC-Co/NiCr/Mo coated Ti-6Al-4V alloy(Elsevier Inc., 2024) Behera, N.; Ramesh, M.R.; Rahman, M.R.The effect of adding Mo to WC-based coatings on the microstructure and dry sliding wear performance at elevated temperatures is investigated. The WC-based coatings are deposited using a high-velocity oxy-fuel process on the titanium-31 substrate. The coating was characterized by microstructure, microhardness, porosity, surface roughness, density, and bond strength. The wear and friction behavior of coatings was evaluated using a ball-on disc tribometer at temperatures of 200, 400, 600, and 800 °C and loads of 20 and 30 N. SEM-EDS and an optical profilometer were utilized to evaluate the wear rate and mechanism. The microhardness and bond strength of WC-CoCr/10%Mo coating is more than that of WC-Co/20%NiCr/10%Mo coatings. The WC-CoCr, WC-CoCr/10%Mo, and WC-Co/20%NiCr/10%Mo coatings exhibited decreasing wear rates up to 600 °C, transitioning to an increase at 800 °C. The oxide phases of CoWO4 WO3 MoO3, CoMoO4, and NiMoO4, formed at 600 °C, aid in reducing the rate of wear and friction coefficient. However, the wear rate slightly increased at 800 °C due to vigorous oxidation and softness of coatings. The friction coefficient of WC-CoCr, WC-CoCr/10%Mo, and WC-Co/20%NiCr/10%Mo coating decreases with increasing temperatures due to the lubricating properties of oxide phases on the worn surface. The WC-CoCr/10%Mo coating demonstrates a lower friction and wear rate than the WC-CoCr and WC-Co/20%NiCr/10%Mo coating. At 200 °C, the predominant wear mechanisms were abrasive and fatigue wear, while at 800 °C, oxidative wear, abrasive wear, and adhesive wear were observed. © 2024Item Microstructure, Mechanical Properties, and Tribological Properties of Fe-Based Composite Coatings Reinforced with WC-Co and Cr3C2(Springer, 2025) Chandramouli, T.V.; Joladarashi, S.; Ramesh, M.R.; Rahman, M.R.Fe-based (stainless steel 316L) coatings are widely employed in the aerospace, chemical processing, petrochemical, and marine industries owing to their low and stable price, excellent corrosion resistance, and durability. However, at elevated temperatures, their performance is limited due to wear. Thus, the current investigation incorporates tungsten carbide (WC-Co) and chromium carbide (Cr3C2) into the Fe-based coating to enhance its wear resistance at high temperatures. SS316L reinforced by 30% of WC-Co and Cr3C2 by mechanical mixture, then sprayed using high-velocity oxy fuel spraying method. Coating characteristics, such as microstructures and phase analysis, were measured using FESEM/EDS and XRD. Coating density, microhardness, and bond strength were examined by water immersion, Vickers indentation, and ASTM C-633 methods, respectively. A ball-on-disk tribometer was employed to conduct wear examination at various temperatures (25, 300, and 600 °C) and loads (10 and 30 N) against the alumina counter body. The wear rate and friction coefficient of SS316L-30%WC-Co decrease from 25 to 600 °C, while the wear rate of SS316L-30%Cr3C2 increases with temperature up to 300 °C and then decreases at 600 °C. The oxide phase adheres strongly to underlying surfaces forming a protective layer (Cr2O3, NiWO4, Fe2O3, and NiMO4), changing the mode of wear mechanism. At higher temperatures and loads, the coating exhibited oxidation modified adhesive wear, and coatings provide excellent wear resistance along with reduction in friction. This research provides a novel approach for future standardization and evaluation of coatings on metal alloys for industrial applications. © ASM International 2024.Item Surface enhancement of SS304 for high-temperature wear resistance using laser cladded Mo-alloyed stellite 6 coatings(Elsevier B.V., 2025) Aprameya, C.R.; Joladarashi, S.; Ramesh, M.R.Severe wear often limits the high-temperature durability of SS304 components, necessitating the development of surface-engineered solutions. In this investigation, Mo-reinforced Stellite 6 claddings were developed using Laser Directed Energy Deposition (L-DED) to provide enhanced surface protection. Claddings with (3, 6, and 9 wt%) Mo reinforcement enhanced hardness by 2.9, 3.1, and 3.3 times, respectively, compared to the SS304 substrate. This improvement is attributed to Mo-induced solid solution strengthening and the formation of hard intermetallic phases. Dry sliding wear tests were conducted at RT and 600 °C under (10 and 20 N) loads. Wear characterisation of the clads was performed using OM, XRD, FE-SEM, EDX, and Raman spectroscopy. At RT, claddings primarily exhibited abrasive wear with minor plastic deformation. However, at 600 °C, the wear mechanism evolved into a combination of severe adhesive, oxidative, abrasive, and plastic deformation modes, with oxidative wear governing the tribological behavior. Stellite 6 with 9 wt% Mo clads exhibited better tribological performance than the other two variants, owing to the development of oxide glaze layers of Cr2O3, NiO, CoO2, and Co3O4. Enhanced performance of the claddings is attributed to solid solution strengthening, Cr-rich carbide formation, increased dislocation density, and the L-DED technology enabling refined microstructure and strong metallurgical bonding. These findings highlight the potential for further advancements in Mo-reinforced Stellite 6 L-DED claddings for high-temperature wear applications. © 2025 Elsevier B.V.