Journal Articles
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/19884
Browse
4 results
Search Results
Item Microstructure and Adhesion Strength of Ni3Ti Coating Prepared by Mechanical Alloying and HVOF(Pleiades Publishing compmg@maik.ru, 2018) Reddy, N.C.; Ajay Kumar, B.S.; Ramesh, M.R.; Koppad, P.G.In the present work we report the development of Ni3Ti intermetallic compound by high energy ball milling of Ni and Ti powders. The ball milled powders were taken at various intervals (4, 6, 8, 10, and 11 h) to analyze the formation of NixTix intermetallic compounds. The ball milled powders were analyzed using scanning electron microscopy and X-ray diffraction. The layered shaped powder particles of Ni3Ti phase were formed after 11 h of ball milling, which was confirmed by X-ray peaks. Further High-Velocity Oxy-Fuel (HVOF) process was used to coat Ni3Ti and Ni3Ti + (Cr3C2 + 20NiCr) on MDN 420 steel. Both the coated materials displayed excellent cohesion with minimal porosity less than 2%. The tensile adhesion strength test was carried out on these coatings to check the bond strength. Out of the two the Ni3Ti coating showed excellent bond strength of 41.04 MPa compared to that of Ni3Ti + (Cr3C2 + 20NiCr) coating. © 2018, Pleiades Publishing, Ltd.Item Elevated temperature solid particle erosion behaviour of carbide reinforced CoCrAlY composite coatings(Institute of Physics Publishing helen.craven@iop.org, 2018) Nithin, H.S.; Desai, V.; Ramesh, M.R.CoCrAlY+WC-Co and CoCrAlY+Cr3C2-NiCr coatings are deposited on nickel based alloy using atmospheric plasma spray technique. Mechanical properties such as microhardness, adhesion strength and fracture toughness of coatings are evaluated. Elevated temperature solid particle erosion behaviour of these coatings are investigated at 600 °C using alumina erodent at 30 and 90° impact angle. Coatings are characterized utilizing Scanning electron microscope (SEM), x-ray diffraction (XRD) and Energy dispersive spectroscopy (EDS). CoCrAlY+WC-Co coating shows higher hardness, adhesion strength and fracture toughness than CoCrAlY+Cr3C2-NiCr coating. CoCrAlY+WC-Co coating exhibited approximately 3 times higher erosion resistance than CoCrAlY+Cr3C2-NiCr coating at 90° and 30° impact angles. SEM images of eroded surfaces of coatings reveals the combination of ductile and brittle fracture. CoCrAlY+Cr3C2-NiCr coating shows severe cracks, craters, carbide pull out and chipping than CoCrAlY+WC-Co coating. High temperature erosion is a combination of simultaneous building up of material by oxidation and removal of material by erosion process. Thus reforming the erosion process to oxidation modified erosion process. © 2018 IOP Publishing Ltd.Item High-Temperature Solid-Particle Erosion Behaviour of Plasma-Sprayed Fe17Cr2Ni0.18C/Cenosphere-Based Composite Coating(Springer Science and Business Media Deutschland GmbH, 2021) Hanumanthlal, S.; Siddaraju, C.; Ramesh, M.R.The present investigation deals to improve the solid-particle erosion resistance of boiler steel material. FeCrNiC and FeCrNiC with 5, 10 and 15wt.% cenosphere composite coatings were deposited on A387 Grade 22 steel using plasma spray technique. Powder and as-sprayed coatings are characterized using Scanning Electron Microscope (SEM), X-ray diffraction to study the surface morphology and cross section to study the nature of coatings deposited. Microhardness and adhesion strength of the coatings are evaluated. High-temperature solid-particle erosion behavior of these coating is evaluated at 300 ºC and 600 ºC at different impact angles. FeCrNiC + 15%Cenosphere designates higher hardness and adhesion strength. Convention weight change method cannot be used to validate the erosion performance due to undesirable variation. Optical profiler is used to determine erosion volume loss. The FeCrNiC coatings with the addition of cenospheres showed better erosion resistance than as-sprayed FeCrNiC and substrate. FeCrNiC + 10%Cenosphere coating shows the highest erosion resistance as compared to other coatings and substrate. Further increase in cenosphere percentage leads to reduction in erosion resistance due to predominant brittle fracture. High-temperature erosion is a concurrent erosion–oxidation process which shows combination of ductile and brittle erosion mechanism. © 2021, The Author(s), under exclusive licence to Springer Nature Switzerland AG.Item A comprehensive characterization of 3D printable poly ether ketone ketone(Elsevier Ltd, 2024) Ojha, N.; Kumar, S.; Ramesh, M.R.; Balan, A.A.S.; Doddamani, M.The current work focuses on the comprehensive characterization of a 3D printable biomaterial, polyether ketone ketone (PEKK). The PEKK granules are first characterized and then utilized for extrusion of the PEKK filaments. The extruded PEKK filaments are characterized for crystallinity, quality, and printability, wherein they exhibit amorphous nature, good quality, and appropriate printability. Utilizing the filaments, the samples are printed with the appropriate printing parameters, which are further characterized for layer adhesion, voids, and crystallinity, wherein they showed seamless layer adhesion, improper beads consolidation, and the amorphous nature. The as printed samples are further annealed at different temperatures (200 and 250 °C). The scanning electron microscopy (SEM) of the annealed samples (A-200 and A-250) revealed better void consolidation, while the X-ray diffraction (XRD) revealed better crystallinity compared to the un-annealed sample. The printed samples are also investigated for dynamic mechanical analysis (DMA), shape memory, and tensile properties. The storage moduli of the annealed samples are observed to be better than the un-annealed sample. The annealed samples exhibited better shape memory properties: shape fixity and shape recovery ratio of A-200 and A-250 samples, 90.28 and 90.75%, and 99.16 and 94.73%, respectively, compared to the un-annealed samples. The highest shape fixity ratio and the shape recovery ratio are noted for A-250 (90.75%) and A-200 (∼ 100%). The A-200 and A-250 samples showed enhanced tensile modulus and strength, 4.16 and 49.67%, and 36.61 and 35.06%, respectively compared to the un-annealed sample. The highest modulus is noted for A-250, while the strength is comparable (36.61 and 35.06%) for A-200 and A-250. © 2023 Elsevier Ltd