Journal Articles
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/19884
Browse
50 results
Search Results
Item Effect of exhaust gas recirculation (EGR) on diesel engine using Simarouba glauca biodiesel blends(Regional Energy Resources Information Center (RERIC) enreric@ait.ac.th, 2015) Bedar, P.; Pandey, J.K.; Kumar, G.N.This article deals with the usage of non-edible Simarouba glauca (paradise) oil as a biodiesel for single cylinder diesel engine with application of exhaust gas recirculation (EGR) rates. Biodiesel blends B10, B20 with EGR rates of 10%, 15%, and 20% are used for different load conditions. Parameters like brake thermal efficiency (BTE), nitrogen oxides (NOx), carbon monoxide (CO), hydrocarbons (HC) and smoke opacity were evaluated from the experimental study. The results show that Simarouba glauca biodiesel usage decreases HC, CO and smoke emissions with slight increase of NOx, also an improvement in the performance was observed for B10 blend. EGR rates 10% and 15% are beneficiated in terms of performance and emission but negative trend is observed for 20% EGR rate. On the whole it is concluded that a better trade-off between NOx and other emissions is attained with simultaneous application of EGR (15%) and biodiesel blend (B10) without compromising engine performance.Item Effect of hydrogen addition on the performance and emission parameters of an SI engine fueled with butanol blends at stoichiometric conditions(Elsevier Ltd, 2015) Raviteja, S.; Kumar, G.N.Hydrogen is considered as the best fuel due to its excellent combustion properties. But its use as a fuel is confined by its low energy density. In the present investigation an attempt has been made to utilize some of the benefits of hydrogen by using it as an additive in a butanol fueled engine. The experimental study has been carried out on a 4 stroke, single cylinder, manifold electronic fuel injected (EFI) engine mapped to run at stoichiometric conditions. Butanol blends were chosen as the base fuel due to their higher energy density compared to ethanol. A small fraction of hydrogen was injected into the air stream. The engine was run at 3000 RPM at full load condition. The performance, emission and combustion parameters are compared for four concentrations of butanol (10%, 20%, 30%, and 100% by volume of fuel) and two concentrations of hydrogen (5%, and 10% by volume of air) with gasoline. The results indicated that the efficiency of the engine improved upon hydrogen enrichment. An average of 60% reduction was observed in HC and CO emissions with 10% enrichment of hydrogen, whereas the NO emissions almost doubled itself. The combustion analysis showed reduced delay periods, shorter combustion durations, higher cylinder pressures, higher temperatures and improved combustion. © 2015 Hydrogen Energy Publications, LLC.Item Experimental Investigation of Variations in Spark Timing using a Spark-Ignition Engine with Hydrogen-Blended Gasoline(Wiley-VCH Verlag info@wiley-vch.de, 2015) Shivaprasad, K.V.; Chitragar, P.R.; Kumar, G.N.This study describes an experiment conducted using an electronically controllable single-cylinder high-speed gasoline engine to analyze the performance and emissions characteristics of various hydrogen-gasoline blends. The experiments have been conducted for various engine speeds and spark timings at the wide open throttle position. The experimental results revealed that the engine brake thermal efficiency and brake mean effective pressure first increase and then decrease with the increase engine speed at all spark timings. The minimum amount of brake specific energy consumption was observed for 20% hydrogen addition in the total fuel blend at 3000rpm engine speed and 14°crank angle (CA) before top dead center (BTDC) spark timing. Hydrocarbon and carbon monoxide emissions were reduced with the retardation of spark timings. Nitrogen oxide emissions were continuously increased with the addition of hydrogen in the fuel blend as well as spark timing advance. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.Item Hydrogen addition on combustion and emission characteristics of high speed spark ignition engine- An experimental study(Taylor's University # 1, Jalan Taylor's Subang Jaya, Selangor Darul Ehsan 47500, 2016) Shivaprasad, K.V.; Chitragar, P.R.; Kumar, G.N.The present article aims at characterizing the combustion and emission parameters of a single cylinder high speed SI engine operating with different concentrations of hydrogen with gasoline fuel. The conventional carburetted SI engine was modified into an electronically controllable engine, wherein ECU was used to control the injection timings and durations of gasoline. The engine was maintained at a constant speed of 3000 rpm and wide open throttle position. The experimental results demonstrated that heat release rate and cylinder pressure were increased with the addition of hydrogen until 20%. The CO and HC emissions were reduced considerably whereas NOx emission was increased with the addition of hydrogen in comparison with pure gasoline engine operation. © School of Engineering, Taylor’s University.Item Performance and emission analysis of a single cylinder CI engine using Simarouba glauca biodiesel(Springer Heidelberg, 2017) Bedar, P.; Chitragar, P.R.; Shivaprasad, K.V.; Kumar, G.N.It is well known fact that diesel engines are commonly used for transportation and power generation due to their high efficiency, low fuel consumption and durability. On contrary these engines churn out harmful and hazardous emissions like particulate matter (PM) and nitrogen oxides (NOx). Recently Bio-origin renewable fuels have taken center stage of discussion because of their ability to replace depleting fossil fuels and capacity to reduce hazardous engine exhausts emissions when used in diesel engines. In the present experimental study Simarouba glauca biodiesel is used in a naturally aspirated four stroke single cylinder air cooled direct injection kirloskar DA10 engine. The main objective is to investigate the effect of biodiesel and exhaust gas recirculation (EGR) on the performance and emission characteristics of a CI engine at 180 bar fuel injection pressure (FIP) with standard injection timing. B20, B40 biodiesel blends with 10, 15 and 20% EGR ratios were used for the study to investigate brake thermal efficiency (BTE), carbon monoxide (CO), unburned hydrocarbons (UBHC), NOx, and smoke opacity. Reduction in CO, HC and smoke opacity is noticed with simarouba biodiesel fuel while increasing NOx compared to diesel. Application of EGR along with biodiesel resulted in simultaneous reduction of nitrogen oxides and smoke without affecting engine performance. It was found from experiment that B20 blend at 15% EGR shown superior performance characteristics compared to other conditions. © Springer India 2017.Item Computational analysis of unsteady flow in turbine part of turbocharger(Springer Heidelberg, 2017) Rao, H.K.S.; Raviteja, S.; Kumar, G.N.Turbocharging technique is widely employed in internal combustion engines to improve the performance and to reduce the exhaust emissions. Flow analysis through the turbocharger has been a guiding method to optimize the turbocharger design. Usually, the turbocharger turbine is analyzed at steady states. But in practical scenario the turbine operates with unsteady flow due to the reciprocating motion of exhaust port and creates unsteady environment in the turbine. In order to increase turbine efficiencies and effective engine turbocharger matching, proper understanding of unsteady flow physics within the turbine is essential. Currently the turbine and compressors maps are obtained by using 1D code which includes extrapolation techniques. These methods neglect heat transfer and windage effects, hence resulting in lower aerodynamic efficiencies. Three dimensional analysis could lead to a better estimation of the flow field, helping the designer to build a high efficiency turbocharger. The present article concentrates on investigating unsteady flow field in the turbine part of a turbocharger. The necessary unsteady conditions at turbine inlet were obtained using commercially available one dimensional engine simulation software AVL Boost. A turbocharged twin cylinder CRDI diesel engine test rig was modelled within the workspace. The exhaust mass flow rate, pressure and temperature were recorded as a function of crank angle. These results were used as the boundary condition for the 3D analysis of the turbine. ANSYS CFX tools were used to solve the unsteady case. The turbine geometry was generated using ANSYS bladegen. The model selected for analysis is k-? turbulence Model. The pulsating performance, effect of secondary flows and entropy generation are discussed in the paper. © Springer India 2017.Item Influence of spark timing on the performance and emission characteristics of gasoline–hydrogen-blended high-speed spark-ignition engine(Taylor and Francis Ltd. michael.wagreich@univie.ac.at, 2017) Shivaprasad, K.V.; Chitragar, P.R.; Nayak, V.; Kumar, G.N.This article experimentally investigates the effect of spark timing on performance and emission characteristics of high-speed spark-ignition (SI) engine operated with different hydrogen–gasoline fuel blends. For this purpose, the conventional carbureted SI engine is modified into an electronically controllable engine, wherein an electronically controllable unit was used to control the ignition timings and injection duration of gasoline. The tests were conducted with different spark timings at the wide open throttle position and 3000 rpm engine speed. The experimental results demonstrated that brake mean effective pressure and engine brake thermal efficiency increased first and then decreased with the increase in spark advance. Peak cylinder pressure, temperature and heat release rate were increased until 20% hydrogen addition and with increased spark timings. NOx emissions were continuously increased with the increment in both spark timings and hydrogen addition, whereas hydrocarbon emissions were increased with spark timings but decreased with hydrogen addition. CO emissions were reduced with the increase in spark timing and hydrogen addition. © 2016 Informa UK Limited, trading as Taylor & Francis Group.Item Combined effect of exhaust gas recirculation (EGR) and fuel injection pressure on CRDI engine operating with jatropha curcas biodiesel blends(Taylor's University # 1, Jalan Taylor's Subang Jaya, Selangor Darul Ehsan 47500, 2017) Bedar, P.; Lamani, V.T.; Ayodhya, A.S.; Kumar, G.N.This work investigates the influence of Exhaust gas recirculation (EGR) and injection pressure on the performance and emissions of CRDI engine using Jatropha curcas biodiesel blends of 10% and 20% (B10 and B20). Experiments were carried out for three fuel injection pressures (FIP) of 300, 400 and 500 bar with 15% and 20% EGR rate at constant speed of 2000 rpm and standard injection timing of 150 BTDC. Parameters like brake thermal efficiency and emission characteristics such as smoke opacity, oxides of nitrogen (NOx), hydrocarbon (HC) and carbon mono-oxide (CO) were measured and analysed. The results showed improvement of performance in terms of brake thermal efficiency for blends B10, B20 and with 15%EGR rate. Smoke, HC and CO decreased while slightly increasing NOx emissions when working with biodiesel. In summary, it is optimized that engine running with combination of B20 blend and 15% EGR rate culminates into NOx reductions without affecting engine efficiency and other emissions like smoke opacity, hydrocarbon and carbon mono-oxide. © School of Engineering, Taylor’s University.Item Effect of hydrogen addition on combustion and emissions performance of a high speed spark ignited engine at idle condition(Serbian Society of Heat Transfer Engineers, 2018) Shivaprasad, K.V.; Chitragar, P.R.; Kumar, G.N.The fuel depletion and environmental pollution have pushed studies on improving the combustion and emission characteristics of internal combustion engines with several alternative fuels. Expert studies proved that hydrogen is one of the prominent energy source which has exceptional combustion qualities that can be used for improving combustion and emissions performance of gasoline-fueled spark ignition engines. This paper introduced an experiment conducted on a single cylinder high speed gasoline engine equipped with a hydrogen injection system to discover the combustion and emissions characteristics with various hydrogen gasoline blends at idle condition. For this purpose, the conventional carburetted high speed spark ignition engine was modified into an electronically controllable engine with help of electronic control unit which dedicatedly used to control the ignition timings and injection duration of gasoline fuel. © 2018 Society of Thermal Engineers of Serbia.Item Experimental study of adiabatic cooling effectiveness on an effusion cooled test plate with machined ring geometries(Begell House Inc. orders@begellhouse.com, 2018) Jesuraj, J.; Rajendran, R.; Kumar, G.N.; Yepuri, Y.G.The present study deals with experimental investigation of adiabatic cooling effectiveness on an effusion cooled test plate with machined ring geometries. Initial tests were performed on an effusion cooling holes. The cooling effectiveness at the beginning of effusion holes is lower, and it increases in the flow direction mainly due to the additive effect of film cooling effectiveness of the effusion cooling geometry. Subsequent tests were done with machined ring geometries fixed ahead of effusion cooling hole geometry to improve the cooling effectiveness before the beginning of effusion cooling holes. These machined ring geometries act as a wall jet and reduce the hot side heat load by film cooling performance. Tests were performed at a coolant to mainstream density ratio of 1.3 and at blowing ratios ranging from 0.5 to 2.5. Increase in the blowing ratio shows an increase in the cooling effectiveness. Comparison results show that the adiabatic cooling effectiveness increases significantly before the effusion cooling holes in the presence of machined ring geometries at all blowing ratios. © 2018 by Begell House, Inc.