Journal Articles
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/19884
Browse
41 results
Search Results
Item Applications of reinforcement particles in the fabrication of Aluminium Metal Matrix Composites by Friction Stir Processing - A Review(EDP Sciences, 2022) Adiga, K.; Herbert, M.A.; Rao, S.S.; Shettigar, A.Composite materials possess advantages like high strength and stiffness with low density and prove their essentiality in the aviation sector. Aluminium metal matrix composites (AMMC) find applications in automotive, aircraft, and marine industries due to their high specific strength, superior wear resistance, and lower thermal expansion. The fabrication of composites using the liquid phase at high temperature leads to the formation of intermetallics and unwanted phases. Friction Stir Processing (FSP) is a novel technique of composite fabrication, with temperature below the melting point of the matrix, achieving good grain refinement. Many researchers reported enhancement of mechanical, microstructure, and tribological properties of AMMC produced by the FSP route. The FSP parameters such as tool rotational speed, tool traverse speeds are found to be having greater impact on uniform dispersion of particles. It is observed that the properties such as tensile strength, hardness, wear and corrosion resistance, are altered by the FSP processes, and the scale of the alterations is influenced significantly by the processing and tool parameters. The strengthening mechanisms responsible for such alterations are discussed in this paper. Advanced engineering materials like shape memory alloys, high entropy alloys, MAX phase materials and intermetallics as reinforcement material are also discussed. Challenges and opportunities in FSP to manufacture AMMC are summarized, providing great benefit to researchers working on FSP technique. ©Item A comprehensive review of friction stir techniques in structural materials and alloys: challenges and trends(Elsevier Editora Ltda, 2022) Prabhakar, D.A.P.; Shettigar, A.; Herbert, M.A.; Gowdru Chandrashekarappa, M.; Pimenov, D.Y.; Giasin, K.; Prakash, C.Friction-stir techniques are the potential alternative to fusion-based systems for processing and welding metallic alloys and other materials. This review explores the advantages, applications, limitations, and future directions of seven friction-based techniques namely, Additive Friction Stir Deposition (AFSD), Friction Stir Additive Manufacturing (FSAM), Friction Stir Welding (FSW), Friction Stir Processing (FSP), Friction Surfacing (FS), Friction Stir Spot Welding (FSSW), and Friction Stir Lap Welding (FSLW). The basic underlying principle of these processes uses friction as a thermal energy source to weld/process/deposit materials. The common control parameters of all friction stir processing techniques are axial force, rotational speed, and weld or traverse speed. In addition, tool profiles and tool dimensions are known to influence the weld quality. The tool's rotational speed and axial force generate friction between the workpiece and tool material interface, which could plasticize the material. The additive powder bed friction stir process (APBFSP) is another new solid-state manufacturing technique that focus on fabricating the polymer matrix nanocomposites (PNC). In this, a hollow tool like AFSD and the fundamental principle of FSP are combined. The said parameters affect the quantity of material getting deposited/welded. However, weld speed/traverse speed alters the weld quality, and higher traverse speed results in porosity and voids in the welded/deposited/processed region. The only difference between AFSD and other friction stir techniques (FSTs) is that in the AFSD technique, the hollow rotating tool comprises two protrusions with different tool profiles (cylindrical, threaded cylindrical, and tapered cylindrical, square) used. Threaded cylindrical profile and tool steel as the tool material is the most commonly employed in FSTs. Apart from that, tungsten carbide is preferred for hard materials. The working principles and process parameters of FSTs that affect the part quality are discussed in detail. The above review gives the reader an understanding of the domain of FSTs that can be researched further. A summary of some of the potential research works with objectives, process parameters, and outcomes is highlighted. This will provide the readers with an overview of the work carried out by researchers across the globe. Finally, the potential research gaps for future directions to be explored soon across the globe are outlined. © 2022 The Author(s).Item A Review of Optimization and Measurement Techniques of the Friction Stir Welding (FSW) Process(Multidisciplinary Digital Publishing Institute (MDPI), 2023) Prabhakar, D.A.P.; Korgal, A.; Shettigar, A.K.; Herbert, M.A.; Gowdru Chandrashekarappa, M.P.G.; Pimenov, D.Y.; Giasin, K.This review reports on the influencing parameters on the joining parts quality of tools and techniques applied for conducting process analysis and optimizing the friction stir welding process (FSW). The important FSW parameters affecting the joint quality are the rotational speed, tilt angle, traverse speed, axial force, and tool profile geometry. Data were collected corresponding to different processing materials and their process outcomes were analyzed using different experimental techniques. The optimization techniques were analyzed, highlighting their potential advantages and limitations. Process measurement techniques enable feedback collection during the process using sensors (force, torque, power, and temperature data) integrated with FSW machines. The use of signal processing coupled with artificial intelligence and machine learning algorithms produced better weld quality was discussed. © 2023 by the authors.Item Tensile properties of cast and mushy state rolled Al-4·5Cu alloy and in situ Al4·5Cu-5TiB2 composite(2010) Herbert, M.A.; Das, G.; Maiti, R.; Chakraborty, M.; Mitra, R.A comparative study has been carried out on tensile properties and failure mechanisms of Al-4·5 wt-%Cu alloy and in situ Al-4·5Cu-5TiB 2 composite in as cast or mushy state rolled conditions. For the alloy, mushy state rolling at temperature for 30 vol.-% nominal liquid content to 2·5% thickness reduction leads to marginally higher strength but poorer ductility, while both these properties worsen significantly on 5% reduction because of grain growth and intergranular solute segregation. Contrarily, mechanical properties of the composite are significantly improved on mushy state rolling at temperatures for 10-30 vol.-% liquid to 2·5-5% reduction. Improvement in mechanical properties of the composite on mushy state rolling is attributed to evolution of globular and finer grains. Examination of fracture surfaces by scanning electron microscope has shown evidence of ductile failure in as cast alloy and in cast or mushy state rolled composite, but that of brittle failure in mushy state rolled alloy. © 2010 W. S. Maney & Son Ltd.Item Effect of mushy state rolling on age-hardening and tensile behavior of Al-4.5Cu alloy and in situ Al-4.5Cu-5TiB2 composite(Elsevier Ltd, 2011) Siddhalingeshwar, I.G.; Herbert, M.A.; Chakraborty, M.; Mitra, R.The effect of mushy state rolling on aging kinetics of stir-cast Al-4.5Cu alloy and in situ Al-4.5Cu-5TiB2 composite and their tensile behavior in solution-treated (495°C) or differently aged (170°C) conditions, has been investigated. As-cast or pre-hot rolled alloy and composite samples were subjected to single or multiple mushy state roll passes to 5% thickness reduction at temperatures for 20% liquid content. Peak-aging times of mushy state rolled composite matrices have been found as ?7.5-10% of that of as-cast alloy. Such enhancement in aging kinetics is attributed to homogeneity in Cu atom distribution as well as increase in matrix dislocation density due to thermal expansion coefficient mismatch between Al and TiB2, matrix grain refinement and particle redistribution, achieved by mushy state rolling. Uniform precipitate distribution in mushy state rolled composite matrices leads to greater peak-age microhardness with higher yield and ultimate tensile strengths than those in as-cast alloy and composite. © 2010 Elsevier B.V.Item Microstructural characterization and hardness evaluation of friction stir welded composite AA6061-4.5Cu-5SiC (Wt.%)(Defense Scientific Information and Documentation Centre, 2013) Shettigar, A.K.; Salian, G.; Herbert, M.A.; Rao, S.Recent developments in advanced materials research have led to the emergence of new materials having features like low density, high strength to weight ratio, excellent mechanical properties, heat and corrosion resistance. In friction stir welding (FSW), a non-consumable rotating welding tool is used to generate the frictional heat and plastic deformation of the material in the welding zone, which is in the solid state. The advantages of FSW as compared to the fusion welding are high joint strength, less defect weld, uniform distribution of grain structure in the weld zone and low power consumption. AA6061 with 4.5 % weight of copper and 5 % weight of SiC composite material has been prepared to conduct experiment and carry out characterization, evaluation of the mechanical properties. Micro-structural characterization of the weld zone is carried out by scanning electron microscope (SEM). Evaluation of hardness was also carried out across the weld zone. A successful method for FSW of AA6061-4.5(wt.%) Cu-5(wt.%) SiC has been developed. © 2013, DESIDOC.Item Correlation of Tribological Properties with Microstructure and Mechanical Properties of Graphite Cast Irons Centrifugally Cast for Engine Liner(Springer India sanjiv.goswami@springer.co.in, 2014) Desai Gowda, H.S.; Mukunda, P.G.; Herbert, M.A.This is a study of the influence of centrifugal process on the graphite morphology, mechanical and wear properties on flake graphite iron (FGI), spheroidal graphite iron (SGI) and compacted graphite iron (CGI). Melts of hypereutectic and almost of identical composition with or without melt treatment were centrifugally cast. The microstructure, mechanical and wear properties of these specimens were studied. In the microstructure for FG iron it has been observed that the centrifugal process produces flake size range class 2–3 (range 160–320 ?m) and graphite of flake type A by about 67.9 % (field %) and combined flakes of type B, C, D and E will be of 32.1 % (field %). While SGI has been observed to have 96.1 % nodules and 330.0 nodules per square millimeter. Similarly CGI has been seen to produce 52.0 % nodules and 113 nodules per square millimeter. SGI possess the highest tensile strength, rupture strain and hardness of 604 N/mm2, 6.1 %, 233 BHN respectively. Whereas FGI possess the least tensile strength, rupture strain and hardness of 303 N/mm2, 0.65 %, 185 BHN respectively among the irons. CGI has a tensile strength, rupture strain and hardness of 369 N/mm2, 1.2 % and 200 BHN respectively which lies in between those of FGI and SGI. During the wear test similar materials for both disk and pin combination show higher co-efficient of friction and wear rate than those for dissimilar material combinations. SGI disk and FGI pin combination show least wear. This combination would be ideally suited for engine liner and piston rings. © 2014, Indian Institute of Metals.Item Microstructure and hardness of friction stir welded aluminium-copper matrix-based composite reinforced with 10 wt-% SiCp(Maney Publishing, 2014) Shettigar, A.; Veeresh Nayak, C.; Herbert, M.A.; Rao, S.S.In the present work, an attempt has been made to join aluminium-copper matrix-based composite reinforced with 10 wt-% SiCp, by the friction stir welding technique, at different combinations of tool rotational speed (710, 1000 and 1400 rev mm1) and welding speed (50, 63 and 80 mm min1) using square profiled friction stir welding tool. Welding parameters play a predominant role in improving the mechanical strength by minimising the defects. A good number of defect free joints were obtained at various combinations of rotational speed and welding speed. It has been observed that, rotational speed and welding speed have strong influence on microstructure, Vickers hardness and quality of welds. © W. S. Maney &Son Ltd 2014.Item Soft computing techniques during drilling of bi-directional carbon fiber reinforced composite(Elsevier Ltd, 2016) Shetty, N.; Herbert, M.A.; Shetty, R.; Shetty, D.S.; Vijay, G.S.Due to the intricacy of machining processes and inconsistency in material properties, analytical models are often unable to describe the mechanics of machining of carbon fiber reinforced polymer (CFRP) composites. Recently, soft computing techniques are used as alternate modeling and analyzing methods, which are usually robust and capable of yielding comprehensive, precise, and unswerving solutions. In this paper, drilling experiments as per the Taguchi L27 experimental layout are carried out on bi-directional carbon fiber reinforced polymer (BD CFRP) composite laminates using three types of drilling tools: high speed steel (HSS), uncoated solid carbide (USC) and titanium nitride coated SC (TiN-SC). The focus of this work is to determine the best drilling tool that produces good quality drilled holes in BD CFRP composite laminates. This paper proposes a novel prediction model 'genetic algorithm optimised multi-layer perceptron neural network' (GA-MLPNN) in which genetic algorithm (GA) is integrated with Multi-Layer Perceptron Neural Network. The performance capability of response surface methodology (RSM) and GA-MLPNN in prediction of thrust force is investigated. RSM is also used to evaluate the influence of process parameters (spindle speed, feed rate, point angle and drill diameter) on thrust force. GA is used to optimize the thrust force and its optimization performance is compared with that of RSM. It is observed that the GA-MLPNN is better predicting tool than the RSM model. The investigation in this paper demonstrates that TiN-SC is the best tool for drilling BD CFRP composite laminates as minimum thrust force is developed during its use. © 2016 Elsevier B.V. All rights reserved.Item Development of novel cutting tool with a micro-hole pattern on PCD insert in machining of titanium alloy(Elsevier Ltd, 2018) Rao, C.M.; Rao, S.S.; Herbert, M.A.The development of a novel cutting tool that had a micro-hole pattern on their rake and flank face of cutting tool surface has found wider potential in the field of manufacturing. Micro-hole pattern features on a tool rake face help in controlling the tribological characteristics of the cutting tool. Micro-holes with the different number of holes orientation, diameter and depth were fabricated using the advanced application of the electrical discharge super drilling machine with the view to assist lubricant penetration and retention. A comparative study has been conducted between micro-hole patterned Polycrystalline Diamond (PCD) cutting insert and the commercially available PCD cutting insert. The effect of micro-hole pattern on the machining of Titanium alloy (Ti-6Al-4 V) is investigated with the application of the Minimum Quantity Lubrication (MQL) method in turning operation. Vibration signals were captured in feed force direction and measured using the tri-axial accelerometer. The cutting temperature, tool-wear, and chip-morphology were measured with an infrared thermometer and Scanning Electron Microscope (SEM). It was found that micro-hole textured inserts reduced the friction on the rake face resulting in the decrease of vibration up to 30–50%. The cutting temperature, tool wear and surface roughness were reduced to 30%, 50% and 40%, respectively. The conical and helical chips were produced in micro pool lubrication system. The friction coefficient can be minimized at the tool-chip interface by using liquid lubrication method. There is no unfavourable effect on the performance of cutting tools having holes on the cutting tool surface. All these parameters led to the improvement in the tool life. © 2018