Journal Articles
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/19884
Browse
5 results
Search Results
Item Development of Zn-Co alloy coatings by pulsed current from chloride bath(2008) Thangaraj, V.; Udayashankar, N.K.; Hegde, A.Zinc-M (where M = Ni, Co and Fe) alloy is of great interest owing to their better mechanical and corrosion properties compared with pure zinc coatings. Corrosion resistance of Zn-Co alloy coatings can be improved considerably by pulse plating. The paper details the optimization of Zn-Co alloy bath using pulsed current and details the superiority of pulse plating over direct current plating. Electroplating of Zn-Co alloys over mild steel was carried out under different conditions of pulse parameters like duty cycle, frequency and peak current density. The production and properties of the deposits were found to be influenced by pulse parameters employed. Within the ranges studied, the bath follows anomalous codeposition with preferential deposition of less noble zinc. The influence of current density on %wt. of Co in the deposit and cathode current efficiencies was studied. It was observed that the deposit at average current density of 5.0 A.dm-2, 50% duty cycle and 100 Hz frequency showed excellent corrosion resistance with fine structure. The peak performance of pulse electrodeposit against corrosion was attributed to the change in the surface homogeneity as evidenced by scanning electron microscope (SEM) image. The drastic decrease of corrosion rate in pulse electrodeposit was attributed to the formation of semiconductor films on the surface as supported by impedance spectroscopy signals.Item Corrosion behavior of composition modulated multilayer Zn-Co electrodeposits produced using a single-bath technique(2009) Thangaraj, V.; Eliaz, N.; Hegde, A.Composition modulated alloy (CMA) electrodeposits of Zn-Co were produced from acid chloride baths by the single-bath technique. Their corrosion behavior was evaluated as a function of the switched cathode current densities and the number of layers. The process was optimized with respect to the highest corrosion resistance. Enhanced corrosion resistance was obtained when the outer layer was slightly richer with cobalt. At the optimum switched current densities 40/55 mA cm-2, a coating with 600 layers showed ~6 times higher corrosion resistance than monolithic Zn-Co electrodeposit having the same thickness. The CMA coating exhibited red rust only after 1,130 h in a salt-spray test. The increased corrosion resistance of the multilayer alloys was related to their inherent barrier properties, as revealed by Electrochemical Impedance Spectroscopy. The corrosion resistance was explained in terms of n-type semiconductor films at the interface as supported by Mott-Schottky plots. © 2008 Springer Science+Business Media B.V.Item Electrodeposition of laminar coatings of Ni-W alloy and their corrosion behaviour(Elsevier, 2015) Elias, L.; Hegde, A.The attractiveness of electroplating for the synthesis of advanced materials is linked to large selection of plating conditions coupled with different mass transfer processes towards the cathode, and this allows the tailoring of different properties of many electrodeposited coatings. This theme has been exploited effectively in the development of a new class of coatings; called composition modulated multilayered (CMM), or in short laminar coatings. The work embodied in this paper is to demonstrate how the corrosion resistance of monolayer Ni-W alloys can be increased to many fold of its magnitude by multilayer deposition. Ni-W coatings have been deposited on mild steel (MS) in a laminar multilayer pattern from a citrate bath using single bath technique (SBT). Electrodeposits having alternate layers of alloys, having different compositions were developed by modulating the direct current (DC). CMM coating configurations have been optimized from a newly developed bath, in terms of current pulse height and thickness of each layer to maximize its corrosion protection ability, in relation to its monolayer coating, developed from same bath for same time. The process and product of the Ni-W coatings have been characterized using different instrumental methods, such as cyclic voltammetry (CV), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD) study. The better corrosion resistance behaviour of CMM Ni-W coatings has been analysed in the light of increased surface areas of the coatings due to layering, and results are discussed. © 2015 Elsevier B.V.Item Development of nanolaminated multilayer Ni-P alloy coatings for better corrosion protection(Royal Society of Chemistry, 2016) Elias, L.; Bhat, K.U.; Hegde, A.Nanolaminated multilayer Nickel-Phosphorous (Ni-P) alloy coatings were developed on mild steel from a citrate bath using glycerol as an additive. Multilayer Ni-P alloy coatings having nanolaminated layers of alloys of alternatively different compositions have been developed using pulsed direct current (DC) by cyclic modulation of the cathode current density. The composition and number (hence thickness) of the layers were tailored by periodic modulation of the current density (c.d.) and time using a programmable power source. The deposition conditions were optimized for both the composition and thickness of the individual layers for the best performance of the coatings against corrosion. Electrochemical corrosion study, evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) demonstrated that the multilayer Ni-P alloy coating with 300 nanolaminated layers, represented as (Ni-P)1.0/4.0/300 showed several fold better corrosion resistance compared to its monolayer counterpart (deposited using regular DC) from the same electrolytic bath. Drastic improvement in the corrosion protection efficacy of the nanolaminated multilayer Ni-P alloy coatings were attributed to an increase in number of interfaces, separating layers of alloys having different morphologies, compositions and phase structures, which was supported by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD) analyses, respectively. The corrosion rates of the multilayer Ni-P alloy coatings were decreased with increasing number of layers, only up to an optimal level and then increased. The increase in corrosion rates at a higher degree of layering were attributed to the diffusion of layers, due to the very short deposition time of each layer. © The Royal Society of Chemistry 2016.Item Single-Layered Zn-Fe Alloy Electrodeposition for The Protection of Mild Steel Structures(Center of Excellence in Electrochemistry, Univ. of Tehran, 2024) Bhat, R.S.; Hegde, A.Electrodeposition of Zinc-Iron alloy has been used to improve the corrosion resistance of mild steel. This alloy plating was successfully coated on mild steel using the electrodeposition technique. Under varied deposition conditions, the zinc-iron alloy films onto the steel plate were examined. The purpose of this study is to describe the corrosion characteristics of the coated sample in 3.5% NaCl for the application of novel, sacrificial coatings for the defence of steel structures. It has been thoroughly examined how plating variables including bath composition, pH, and current density affect the composition, morphology; and corrosion properties of the coatings were discussed. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) are used to analyze the morphological characteristics and phase structure of the coatings. The surface roughness of the coating was measured by Atomic Force Microscopy (AFM). The Vickers indenter was employed to measure the microhardness of the coated sample. The corrosion resistance of Zn-Fe alloy coatings was assessed using electrochemical impedance spectroscopy (EIS) and polarization techniques at different current densities. The new low-cost Zn-Fe alloy coating was used for automobile applications. © 2024 by CEE (Center of Excellence in Electrochemistry).