Journal Articles
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/19884
Browse
6 results
Search Results
Item Corrosion behavior of composition modulated multilayer Zn-Co electrodeposits produced using a single-bath technique(2009) Thangaraj, V.; Eliaz, N.; Hegde, A.Composition modulated alloy (CMA) electrodeposits of Zn-Co were produced from acid chloride baths by the single-bath technique. Their corrosion behavior was evaluated as a function of the switched cathode current densities and the number of layers. The process was optimized with respect to the highest corrosion resistance. Enhanced corrosion resistance was obtained when the outer layer was slightly richer with cobalt. At the optimum switched current densities 40/55 mA cm-2, a coating with 600 layers showed ~6 times higher corrosion resistance than monolithic Zn-Co electrodeposit having the same thickness. The CMA coating exhibited red rust only after 1,130 h in a salt-spray test. The increased corrosion resistance of the multilayer alloys was related to their inherent barrier properties, as revealed by Electrochemical Impedance Spectroscopy. The corrosion resistance was explained in terms of n-type semiconductor films at the interface as supported by Mott-Schottky plots. © 2008 Springer Science+Business Media B.V.Item Surface modification by multilayered Zn-Co alloy coatings(2012) Yogesha, S.; Udupa, K.R.; Hegde, A.Nanostructured multilayer alloy or composition modulated multilayer alloy coatings of Zn-Co have been developed, and their corrosion behaviours were studied by potentiodynamic polarization and electrochemical impedance spectroscopy methods. The coatings were developed galvanostatically using square, triangular and sawtooth current pulses through single bath technique. The cyclic cathode current density and the numbers of layers have been optimised for peak performance of the coatings against corrosion. Under optimal conditions, the coatings developed using square, triangular and sawtooth current pulses were found to be respectively y100, 80 and 90 times more corrosion resistant than monolithic alloy of same thickness. The better corrosion resistances of the composition modulated multilayer alloy coatings were attributed to the dielectric barrier at the interface, as evidenced by dielectric spectroscopy. Surface morphology, multilayer formation and surface after corrosion tests were examined by scanning electron microscopy. © 2012 Institute of Materials, Minerals and Mining.Item Electrolytic Synthesis and Characterization of Electrocatalytic Ni-W Alloy(Springer New York LLC barbara.b.bertram@gsk.com, 2015) Elias, L.; Scott, K.; Hegde, A.Inspired by the more positive (about 0.38 V nobler) discharge potential of hydrogen on Ni-W alloy compared to that on both Ni and W, a Ni-W alloy has been developed electrolytically as an efficient electrode material for water electrolysis. The deposition conditions, for peak performance of the electrodeposits for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in 1.0 M KOH medium have been optimized. Electrocatalytic activity of the coatings, deposited at different current densities (c.d.’s) for water splitting reactions of HER and OER was tested by cyclic voltammetry and chronopotentiometry. It was found that Ni-W alloys deposited, at 4.0 A/dm2 (having about 12.49 wt.% W) and 1.0 A/dm2 (having about 0.95 wt.% W) are good electrode materials as cathode (for HER) and anode (for OER), respectively. A dependency of the electrocatalytic activity for HER and OER with relative amount of Ni and W, in the deposit was found. The variation of electrocatalytic activity with W content showed the existence of a synergism between high-catalytic property of W (due to low hydrogen overvoltage) and Ni (having increased adsorption of OH? ions), for hydrogen (as cathode) and oxygen (as anode) evolution, respectively. Electrocatalytic activities of the coatings, developed at different c.d.’s were explained in the light of their phase structure, surface morphology, and chemical composition, confirmed by XRD, FESEM, and EDX analysis. The effect of c.d. on thickness, hardness, composition, HER, and OER was analyzed, and results were discussed with possible mechanisms. © 2015, ASM International.Item Electrodeposition of laminar coatings of Ni-W alloy and their corrosion behaviour(Elsevier, 2015) Elias, L.; Hegde, A.The attractiveness of electroplating for the synthesis of advanced materials is linked to large selection of plating conditions coupled with different mass transfer processes towards the cathode, and this allows the tailoring of different properties of many electrodeposited coatings. This theme has been exploited effectively in the development of a new class of coatings; called composition modulated multilayered (CMM), or in short laminar coatings. The work embodied in this paper is to demonstrate how the corrosion resistance of monolayer Ni-W alloys can be increased to many fold of its magnitude by multilayer deposition. Ni-W coatings have been deposited on mild steel (MS) in a laminar multilayer pattern from a citrate bath using single bath technique (SBT). Electrodeposits having alternate layers of alloys, having different compositions were developed by modulating the direct current (DC). CMM coating configurations have been optimized from a newly developed bath, in terms of current pulse height and thickness of each layer to maximize its corrosion protection ability, in relation to its monolayer coating, developed from same bath for same time. The process and product of the Ni-W coatings have been characterized using different instrumental methods, such as cyclic voltammetry (CV), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD) study. The better corrosion resistance behaviour of CMM Ni-W coatings has been analysed in the light of increased surface areas of the coatings due to layering, and results are discussed. © 2015 Elsevier B.V.Item Development of nanolaminated multilayer Ni-P alloy coatings for better corrosion protection(Royal Society of Chemistry, 2016) Elias, L.; Bhat, K.U.; Hegde, A.Nanolaminated multilayer Nickel-Phosphorous (Ni-P) alloy coatings were developed on mild steel from a citrate bath using glycerol as an additive. Multilayer Ni-P alloy coatings having nanolaminated layers of alloys of alternatively different compositions have been developed using pulsed direct current (DC) by cyclic modulation of the cathode current density. The composition and number (hence thickness) of the layers were tailored by periodic modulation of the current density (c.d.) and time using a programmable power source. The deposition conditions were optimized for both the composition and thickness of the individual layers for the best performance of the coatings against corrosion. Electrochemical corrosion study, evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) demonstrated that the multilayer Ni-P alloy coating with 300 nanolaminated layers, represented as (Ni-P)1.0/4.0/300 showed several fold better corrosion resistance compared to its monolayer counterpart (deposited using regular DC) from the same electrolytic bath. Drastic improvement in the corrosion protection efficacy of the nanolaminated multilayer Ni-P alloy coatings were attributed to an increase in number of interfaces, separating layers of alloys having different morphologies, compositions and phase structures, which was supported by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD) analyses, respectively. The corrosion rates of the multilayer Ni-P alloy coatings were decreased with increasing number of layers, only up to an optimal level and then increased. The increase in corrosion rates at a higher degree of layering were attributed to the diffusion of layers, due to the very short deposition time of each layer. © The Royal Society of Chemistry 2016.Item Magnetoelectrodeposition of Ni-W alloy coatings for enhanced hydrogen evolution reaction(Royal Society of Chemistry, 2016) Elias, L.; Cao, P.; Hegde, A.The electrocatalytic efficiency of electrodeposited (ED) Ni-W alloy coatings for the hydrogen evolution reaction (HER) has been improved drastically through magnetoelectrodeposition (MED) approach. Ni-W alloy coatings have been developed under different conditions of magnetic field intensity 'B' (applied perpendicular in the range of 0.1-0.4 T), and their electrocatalytic activity for the HER has been tested using cyclic voltammetry (CV) and chronopotentiometry (CP) techniques in 1.0 M KOH solution. A drastic improvement in the electrocatalytic behavior of the MED coating, represented as (Ni-W)B=0.2 T was found as compared to its conventional Ni-W alloy coatings. Improved performance of the MED coatings was explained on the basis of differences in the process of electrocrystallization affected due to the applied magnetic field, supported by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analyses. A magnetic field has been used advantageously for the first time to increase the W content of the alloy. Increased activity of the MED coatings was attributed to the increased W content in the alloy, characterized by the unique (220) reflection, explained by the magnetohydrodynamic (MHD) effect due to Lorentz force. © 2016 The Royal Society of Chemistry.