Journal Articles
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/19884
Browse
4 results
Search Results
Item Additive Manufacturing of Syntactic Foams: Part 2: Specimen Printing and Mechanical Property Characterization(Minerals, Metals and Materials Society 184 Thorn Hill Road Warrendale PA 15086, 2018) Singh, A.K.; Saltonstall, B.; Patil, B.; Hoffmann, N.; Doddamani, M.; Gupta, N.High-density polyethylene (HDPE) and its fly ash cenosphere-filled syntactic foam filaments have been recently developed. These filaments are used for three-dimensional (3D) printing using a commercial printer. The developed syntactic foam filament (HDPE40) contains 40 wt.% cenospheres in the HDPE matrix. Printing parameters for HDPE and HDPE40 were optimized for use in widely available commercial printers, and specimens were three-dimensionally (3D) printed for tensile testing at strain rate of 10?3 s?1. Process optimization resulted in smooth operation of the 3D printer without nozzle clogging or cenosphere fracture during the printing process. Characterization results revealed that the tensile modulus values of 3D-printed HDPE and HDPE40 specimens were higher than those of injection-molded specimens, while the tensile strength was comparable, but the fracture strain and density were lower. © 2018, The Minerals, Metals & Materials Society.Item Generalized optimization procedure for rotational magnetized direction permanent magnet thrust bearing configuration(SAGE Publications Ltd info@sagepub.co.uk, 2019) Bekinal, S.I.; Doddamani, M.; Vanarotti, M.; Jana, S.Optimization of rotational magnetized direction permanent magnet thrust bearing configuration is carried out using generalized three-dimensional mathematical model. The bearing features namely axial force and stiffness are maximized using in-house developed mathematical expressions solved using MATLAB. The design variables selected for the optimization are axial offset, number of ring pairs, air gap and inner radius of inner and outer rings. The maximized axial force values of the optimized configuration are validated with the finite element analysis results. To overcome the high computational cost associated with three-dimensional equations, generalized method of optimization is sucessfully demonstrated using plots representing variation of optimal design variables as a function of air gap with respect to bearing’s outer diameter. Simple and useful method of using the generalized plots for the process of optimization is presented by dimension optimization of representative bearing configuration with a particular aspect ratio. The proposed optimization using mathematical model and generalized approach assists designer in selecting optimized geometrical parameters of rotational magnetized direction thrust bearing configurations easily for variety of high-speed applications. © IMechE 2018.Item Design and Optimization of Multi-ring Permanent Magnet Bearings for High-speed Rotors - A Computational Framework(Engineered Science Publisher, 2021) Kamath, C.R.; Bhat, R.; Bekinal, S.I.; Vijay, G.S.; Shetty, T.S.; Doddamani, M.This article presents a computational framework (MATLAB app) suitable for the industrial use for selecting optimum multi-ring radial and thrust permanent magnet bearings (PMB) based on two general variables (outer diameter/air gap and length of a bearing). Such an approach eliminates the usage of complex design equations and optimization methods. The detailed methodology adopted in optimizing PMB for maximum characteristics is presented with mathematical equations of force and stiffness. Then, the steps involved in the development of the computational framework are discussed in depth. Further, usage of the computational framework is explained with examples of PMB, and results obtained are validated with the mathematical model results. Regarding the mathematical model results, deviations of 2.22 % and 1.78 % are observed among the maximized radial and axial force values in the app results. Finally, the effectiveness of the proposed framework is demonstrated by discussing the case studies from the literature. © Engineered Science Publisher LLC 2021.Item Additive Manufacturing of Short Silk Fiber Reinforced PETG Composites(Elsevier Ltd, 2022) Kn, V.; Bonthu, D.; Doddamani, M.; Pati, F.The growing demand for customized medical devices like prostheses, orthoses, and implants is the prime motive for a surge in the investigation of 3D printable biocomposites. PETG (Polyethylene terephthalate glycol) based composites can be a good choice for biomedical applications. Specific characteristics of this material like biocompatibility, ease of formability, stable thermomechanical properties, and high chemical, and abrasion resistance make it suitable for biomedical applications. However, there are very few studies on the 3D printing of PETG-based composites. Development of a robust 3D printing protocol is required for any novel natural fiber reinforced PETG composites. This study presents natural fiber-reinforced PETG biocomposite filament preparation and 3D printing with the developed composite filaments. Silk was used as a filler material due to its high thermal stability and high tensile strength. Composite filaments with 2 wt%, 5 wt%, and 10 wt% silk were prepared using the extrusion process. Further, we developed a protocol for 3D printing with the developed composites to fabricate various 3D structure. Both filaments and printed specimens were characterized morphologically, structurally, and mechanically. The melt flow rate of the filaments decreased with an increase in fiber content which was a bottleneck for printing 10% silk-PETG composites. Micro-CT results validate an increase in void content in filaments on filler addition. The highest flexural modulus and flexural strength were exhibited by 2% silk-PETG printed parts and a 60% increase in compressive modulus compared to pure PETG. Tensile tests show that 2 wt% fiber addition significantly increased elastic modulus (2466.72 MPa) compared to pure PETG (902.81 MPa), whereas the surface roughness of printed composites increased with filler content. Finally, a lower limb prosthetic socket prototype was printed with a desktop 3D printer to demonstrate its potential for biomedical applications. © 2022 Elsevier Ltd