Journal Articles
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/19884
Browse
7 results
Search Results
Item Enhancement of the properties of fly ash based geopolymer paste by incorporating ground granulated blast furnace slag(Elsevier Ltd, 2017) Saha, S.; C, C.Research efforts have been made continuously to establish fly ash based geopolymer as an alternative binder material for the production of fresh concrete because production of Ordinary Portland Cement degrades the environment by huge emissions of carbon-di-oxide and also by consuming lot of natural resources. But most of the study reveals, fly ash based geopolymer paste needs more time to get set when it is cured at ambient temperature. As a result, it is quite impractical to use fly ash based geopolymer paste as an alternative to Ordinary Portland Cement in faster construction. In this study, an effort has been made to enhance the properties of fly ash based geopolymer paste by incorporating ground granulated blast furnace slag at various percentage levels. Microstructure of the geopolymer paste is studied using Scanning Electron Microscopy. Result of this investigation shows that significant improvement on setting time and compressive strength can be obtained by adding ground granulated blast furnace slag in the mixes. © 2017 Elsevier LtdItem Investigation on the potential use of recycled fine aggregate to produce geopolymer mortar mix(ASTM International, 2019) Saha, S.; C, C.The utilization of construction and demolition waste (C&DW) partially or fully for various purposes in construction industries is one of the most significant solutions to overcome the scarcity of raw materials and disturbances of the environmental system. On the other hand, geopolymer is being tried to be established as an alternative sustainable binder material for ordinary portland cement. In the present study, with the thought of promoting of sustainability, an attempt has been made to use concrete wastes as recycled fine aggregate (RFA) partially to produce fly ash (FA)-based geopolymer mortar. The workability, water absorption, compressive strength at 3, 7, 28, and 56 days, volume change behavior, and chloride permeability of the produced FA-based geopolymer mortar were determined. The effects of RFA, the ratio of alkali liquid (AL) to FA, and different curing regimes on these properties of mortar mix also discussed. The morphology and microstructures of the samples taken from the mortar mix, which were observed having the highest strength under different curing regimes, were studied using scanning electron microscopy (SEM). The experimental results indicate lower workability, higher water absorption capacity, and higher drying shrinkage of geopolymer mortar mix that has more RFA content in the mix, but the compressive strength of the geopolymer mortar mix started decreasing after a certain percentage of RFA content in the mix. Utilization of that certain percentage of RFA will help us to minimize the consumption of natural fine aggregates and reduce the disturbances generated by unorganized dumping of C&DW. © 2019 by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959.Item Characterization and performance of processed lateritic fine aggregates in cement mortars and concretes(Elsevier Ltd, 2019) Yaragal, S.C.; Basavana Gowda, S.N.; C, C.Availability of river sand is becoming scarce, due to rapid increase in infrastructure projects in India. Acute shortage of river sand, has led to indiscriminate sand mining. Adverse effect of sand mining includes river bank erosion, river bed degradation, loss of biodiversity and deterioration of river water quality and ground water availability. To address the above issues, research efforts are on, to find substitutes for river sand to be used as fine aggregate in mortars and concretes. One among the locally available resources is laterite. Laterite is a product of tropical or sub-tropical weathering, which is an abundant soil material in many parts of India. An attempt has been made to characterize the processing technique to obtain good quality lateritic fine aggregates (lateritic FA). Experiments were designed and conducted to study the performance of lateritic FA as replacement to river sand, in cement mortars and concretes. Processed lateritic FA in replacement levels of 0, 25, 50, 75 and 100 wt% to river sand at all fineness levels (Zone I to Zone IV as per Indian standards) is considered. Microstructure studies were conducted to understand the arrangement of river sand and lateritic FA with cement matrix and their Interfacial Transition Zones (ITZ) using Scanning Electron Microscope (SEM). The workability and compressive strength characteristics of cement mortars and concretes are evaluated. Laterized mortars with Zone III and Zone IV fine aggregates, at all replacement levels, result in the same compressive strengths as those of control mortars. Suitable strength enhancement technique has been attempted to achieve strengths of Zone I and Zone II lateritic fine aggregates based mortars at 100 wt% replacement, to achieve strength at least equal to or more than those of control mortars. Laterized concretes have achieved nearly the same strengths as those of control concretes, at all replacement levels and for all fineness levels (Zone I to Zone IV). © 2018 Elsevier LtdItem Volume change characteristics of eco-friendly mortar mixes produced with geopolymeric binder and recycled fine aggregate(ASTM International, 2020) Saha, S.; Shaik, N.; C, C.The production of geopolymer mortar using recycled fine aggregate (RFA) generated from concrete waste has significant potential to be a sustainable construction material. In this article, the volume change properties of the produced geopolymer mortar mixes are studied in terms of drying shrinkage up to the age of 180 days and reported as the percentage increase with respect to the shrinkage value of 3 days. The influence of RFA content, alkaline liquid (AL) in terms of the concentration of sodium hydroxide (SH) solution, the ratio of sodium silicate (SS) solution to SH solution, and the ratio of AL to fly ash (FA) were investigated on the drying shrinkage properties of the geopolymer mortar mixes. All the cast specimens were cured at 80°C for 24 hours. Higher drying shrinkage values were observed for the mortar mixes produced with higher RFA content, AL/FA, SS/SH ratio, and lower concentration of SH solution. Scanning electron microscope images were studied for the samples taken from the geopolymer mixes showing lower drying shrinkage values to understand the microstructure. © 2019 by ASTM International.Item Strength and shrinkage properties of heat-cured fly ash-based geopolymer mortars containing fine recycled concrete aggregate(ASTM International, 2020) Saha, S.; C, C.Geopolymer has obtained significant importance as an alternative eco-friendly binder material for ordinary portland cement (OPC) as it can be produced from the reaction between the industrial by-product materials rich in alumina, silica, and alkaline solutions. Therefore, usage of geopolymer effectively in the construction industry will help to reduce the consumption of a huge quantity of natural resources for the energy processes required for the production of OPC. It is also one of important solution to control carbon dioxides emission by the usage of OPC. On the other hand, using construction and demolition waste (C&DW) as the source of recycled aggregates in construction industry helps to reduce the huge consumption of natural aggregates and protect the environment from the disturbances caused by the unorganized dumping of C&DW. In this study, an attempt has been madeto produce fly ash (FA)-based geopolymer mortar mixes using C&DW effectively as fine aggregates partially. The effects of recycled fine aggregates (RFA), the ratio of alkaline liquid (AL) to FA, and duration of heat curing on the properties of the produced geo-polymer mortar mixes have been discussed in this article. To determine the influence of RFA on the strength and volume change behavior of mixes, natural fine aggregates were replaced by RFA at 0, 10, 20, 30, 40, and 50 % by mass. The AL/FA ratio was adopted as 0.4 and 0.6. Higher compressive strength was observed for most of the mortar mixes having RFA up to 20 %, and higher drying shrinkage value was found for the mixes with higher RFA content. Scanning electron microscopy (SEM) images were also studied for knowledge about the signature of the formed structures in the mortar mixes, which were observed having higher strength. © © 2019 by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959.Item Study on Durability Properties of Sustainable Alternatives for Natural Fine Aggregate(Springer, 2021) Arpitha, D.; C, C.The present work focused on the durability performance of copper slag (CS) and processed granulated blast furnace slag (PGBS) as a partial replacement (0% to 50%) for natural fine aggregate (NFA) in concrete, cured for 365 days. This work was carried out to determine the ingression of chloride, sulphate, and sodium ions. Compressive strength test and splitting tensile test conducted for the specimens showed that PGBS concrete attained higher strength followed by CS concrete when compared to conventional concrete. The ingression of chloride and sulphate ions decreased in both CS and PGBS concrete after 90 days of curing. Sodium ions ingression also decreased after 180 days of curing. Microstructure studies were carried out using scanning electron microscope (SEM) which showed the dense formation of C–S–H gel in the matrix and high amount of Ca and Si ions in CS and PGBS concrete was observed using energy-dispersive spectroscopy (EDS) analysis. The basic properties like particle size and water absorption of CS and PGBS aggregates have majorly contributed in the reduction in voids in concrete. PGBS concrete has found to be an effective alternative in terms of performance, cost, availability, and environmentally friendly when compared to already exiting CS aggregates and NFA. © 2021, The Institution of Engineers (India).Item Performance and microstructural investigations of processed lateritic fine aggregates in blended cement mortars exposed to elevated temperatures(Emerald Publishing, 2023) Basavana Gowda, S.N.; Yaragal, S.C.; C, C.; Goudar, S.K.Purpose: In recent years, fire accidents in engineering structures have often been reported worldwide, leading to a severe risk to life and property safety. The present study is carried out to evaluate the performance of Ground Granulated Blast Furnace Slag (GGBS) and fly ash–blended laterized mortars at elevated temperatures. Design/methodology/approach: This test program includes the replacement of natural river sand with lateritic fine aggregates (lateritic FA) in terms of 0, 50 and 100%. Also, the ordinary Portland cement (OPC) was replaced with fly ash and GGBS in terms of 10, 20, 30% and 20, 40 and 60%, respectively, for producing blended mortars. Findings: This paper presents results related to the determination of residual compressive strengths of lateritic fine aggregates-based cement mortars with part replacement of cement by fly ash and GGBS exposed to elevated temperatures. The effect of elevated temperatures on the physical and mechanical properties was evaluated with the help of microstructure studies and the quantification of hydration products. Originality/value: A sustainable cement mortar was produced by replacing natural river sand with lateritic fine aggregates. The thermal strength deterioration features were assessed by exposing the control specimens and lateritic fine aggregates-based cement mortars to elevated temperatures. Changes in the mechanical properties were evaluated through a quantitative microstructure study using scanning electron microscopy (SEM) images. The phase change of hydration products after exposure to elevated temperatures was qualitatively analyzed by greyscale thresholding of SEM images using Image J software. © 2023, Emerald Publishing Limited.