Journal Articles
Permanent URI for this collectionhttps://idr.nitk.ac.in/handle/123456789/19884
Browse
10 results
Search Results
Item Enhancement of the properties of fly ash based geopolymer paste by incorporating ground granulated blast furnace slag(Elsevier Ltd, 2017) Saha, S.; C, C.Research efforts have been made continuously to establish fly ash based geopolymer as an alternative binder material for the production of fresh concrete because production of Ordinary Portland Cement degrades the environment by huge emissions of carbon-di-oxide and also by consuming lot of natural resources. But most of the study reveals, fly ash based geopolymer paste needs more time to get set when it is cured at ambient temperature. As a result, it is quite impractical to use fly ash based geopolymer paste as an alternative to Ordinary Portland Cement in faster construction. In this study, an effort has been made to enhance the properties of fly ash based geopolymer paste by incorporating ground granulated blast furnace slag at various percentage levels. Microstructure of the geopolymer paste is studied using Scanning Electron Microscopy. Result of this investigation shows that significant improvement on setting time and compressive strength can be obtained by adding ground granulated blast furnace slag in the mixes. © 2017 Elsevier LtdItem Investigation on the potential use of recycled fine aggregate to produce geopolymer mortar mix(ASTM International, 2019) Saha, S.; C, C.The utilization of construction and demolition waste (C&DW) partially or fully for various purposes in construction industries is one of the most significant solutions to overcome the scarcity of raw materials and disturbances of the environmental system. On the other hand, geopolymer is being tried to be established as an alternative sustainable binder material for ordinary portland cement. In the present study, with the thought of promoting of sustainability, an attempt has been made to use concrete wastes as recycled fine aggregate (RFA) partially to produce fly ash (FA)-based geopolymer mortar. The workability, water absorption, compressive strength at 3, 7, 28, and 56 days, volume change behavior, and chloride permeability of the produced FA-based geopolymer mortar were determined. The effects of RFA, the ratio of alkali liquid (AL) to FA, and different curing regimes on these properties of mortar mix also discussed. The morphology and microstructures of the samples taken from the mortar mix, which were observed having the highest strength under different curing regimes, were studied using scanning electron microscopy (SEM). The experimental results indicate lower workability, higher water absorption capacity, and higher drying shrinkage of geopolymer mortar mix that has more RFA content in the mix, but the compressive strength of the geopolymer mortar mix started decreasing after a certain percentage of RFA content in the mix. Utilization of that certain percentage of RFA will help us to minimize the consumption of natural fine aggregates and reduce the disturbances generated by unorganized dumping of C&DW. © 2019 by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959.Item Characterization and performance of processed lateritic fine aggregates in cement mortars and concretes(Elsevier Ltd, 2019) Yaragal, S.C.; Basavana Gowda, S.N.; C, C.Availability of river sand is becoming scarce, due to rapid increase in infrastructure projects in India. Acute shortage of river sand, has led to indiscriminate sand mining. Adverse effect of sand mining includes river bank erosion, river bed degradation, loss of biodiversity and deterioration of river water quality and ground water availability. To address the above issues, research efforts are on, to find substitutes for river sand to be used as fine aggregate in mortars and concretes. One among the locally available resources is laterite. Laterite is a product of tropical or sub-tropical weathering, which is an abundant soil material in many parts of India. An attempt has been made to characterize the processing technique to obtain good quality lateritic fine aggregates (lateritic FA). Experiments were designed and conducted to study the performance of lateritic FA as replacement to river sand, in cement mortars and concretes. Processed lateritic FA in replacement levels of 0, 25, 50, 75 and 100 wt% to river sand at all fineness levels (Zone I to Zone IV as per Indian standards) is considered. Microstructure studies were conducted to understand the arrangement of river sand and lateritic FA with cement matrix and their Interfacial Transition Zones (ITZ) using Scanning Electron Microscope (SEM). The workability and compressive strength characteristics of cement mortars and concretes are evaluated. Laterized mortars with Zone III and Zone IV fine aggregates, at all replacement levels, result in the same compressive strengths as those of control mortars. Suitable strength enhancement technique has been attempted to achieve strengths of Zone I and Zone II lateritic fine aggregates based mortars at 100 wt% replacement, to achieve strength at least equal to or more than those of control mortars. Laterized concretes have achieved nearly the same strengths as those of control concretes, at all replacement levels and for all fineness levels (Zone I to Zone IV). © 2018 Elsevier LtdItem Performance of eco-friendly mortar mixes against aggressive environments(Techno-Press info@techno-press.com, 2020) Saha, S.; C, C.; Gupta, P.Past research efforts already established geopolymer as an environment-friendly alternative binder system for ordinary Portland cement (OPC) and recycled aggregate is also one of the promising alternative for natural aggregates. In this study, an effort was made to produce eco-friendly mortar mixes using geopolymer as binder and recycled fine aggregate (RFA) partially and study the resistance ability of these mortar mixes against the aggressive environments. To form the geopolymer binder, 70% fly ash, 30% ground granulated blast furnace slag (GGBS) and alkaline solution comprising of sodium silicate solution and 14M sodium hydroxide solution with a ratio of 1.5 were used. The ratio of alkaline liquid to binder (AL/B) was also considered as 0.4 and 0.6. In order to determine the resistance ability against aggressive environmental conditions, acid attack test, sulphate attack test and rapid chloride permeability test were conducted. Change in mass, change in compressive strength of the specimens after the immersion in acid/sulphate solution for a period of 28, 56, 90 and 120 days has been presented and discussed in this study. Results indicated that the incorporation of RFA leads to the reduction in compressive strength. Even though strength reduction was observed, eco-friendly mortar mixes containing geopolymer as binder and RFA as fine aggregate performed better when it was produced with AL/B ratio of 0.6. © 2020 Techno-Press, Ltd.Item Strength and shrinkage properties of heat-cured fly ash-based geopolymer mortars containing fine recycled concrete aggregate(ASTM International, 2020) Saha, S.; C, C.Geopolymer has obtained significant importance as an alternative eco-friendly binder material for ordinary portland cement (OPC) as it can be produced from the reaction between the industrial by-product materials rich in alumina, silica, and alkaline solutions. Therefore, usage of geopolymer effectively in the construction industry will help to reduce the consumption of a huge quantity of natural resources for the energy processes required for the production of OPC. It is also one of important solution to control carbon dioxides emission by the usage of OPC. On the other hand, using construction and demolition waste (C&DW) as the source of recycled aggregates in construction industry helps to reduce the huge consumption of natural aggregates and protect the environment from the disturbances caused by the unorganized dumping of C&DW. In this study, an attempt has been madeto produce fly ash (FA)-based geopolymer mortar mixes using C&DW effectively as fine aggregates partially. The effects of recycled fine aggregates (RFA), the ratio of alkaline liquid (AL) to FA, and duration of heat curing on the properties of the produced geo-polymer mortar mixes have been discussed in this article. To determine the influence of RFA on the strength and volume change behavior of mixes, natural fine aggregates were replaced by RFA at 0, 10, 20, 30, 40, and 50 % by mass. The AL/FA ratio was adopted as 0.4 and 0.6. Higher compressive strength was observed for most of the mortar mixes having RFA up to 20 %, and higher drying shrinkage value was found for the mixes with higher RFA content. Scanning electron microscopy (SEM) images were also studied for knowledge about the signature of the formed structures in the mortar mixes, which were observed having higher strength. © © 2019 by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959.Item Compressive strength prediction of SCC containing fly ash using SVM and PSO-SVM models(Structural Engineering Research Centre, 2021) Rajeshwari, R.; Mandal, S.; C, C.Self-Compacting Concrete (SCC), is a highly workable material, compacted by its self weight without observable segregation and bleeding. In this study, Support Vector Machine (SVM) and particle swarm optimization based SVM models are employed to predict the 28 days compressive strength of individual SCC mix. A database of 62 no’s of SCC compressive strength from literature with cement partially replaced by fly ash is used for training the models. The test data consists of two groups, an individual study consisting of 9 datasets and other combination of three studies with 19 datasets tested separately. Similar input parameters from the train data is extended for testing the models prediction accuracy. Statistical parameters such as correlation coefficient, root mean square error and scatter index are used to evaluate the models’ prediction results. The particle swarm optimization based SVM model is capable of selecting appropriate SVM parameters to increase the prediction accuracy. From the results, it is seen that both SVM and particle swarm optimized SVM models have good capability in predicting the SCC compressive strength. © 2021, Structural Engineering Research Centre. All rights reserved.Item Study on Durability Properties of Sustainable Alternatives for Natural Fine Aggregate(Springer, 2021) Arpitha, D.; C, C.The present work focused on the durability performance of copper slag (CS) and processed granulated blast furnace slag (PGBS) as a partial replacement (0% to 50%) for natural fine aggregate (NFA) in concrete, cured for 365 days. This work was carried out to determine the ingression of chloride, sulphate, and sodium ions. Compressive strength test and splitting tensile test conducted for the specimens showed that PGBS concrete attained higher strength followed by CS concrete when compared to conventional concrete. The ingression of chloride and sulphate ions decreased in both CS and PGBS concrete after 90 days of curing. Sodium ions ingression also decreased after 180 days of curing. Microstructure studies were carried out using scanning electron microscope (SEM) which showed the dense formation of C–S–H gel in the matrix and high amount of Ca and Si ions in CS and PGBS concrete was observed using energy-dispersive spectroscopy (EDS) analysis. The basic properties like particle size and water absorption of CS and PGBS aggregates have majorly contributed in the reduction in voids in concrete. PGBS concrete has found to be an effective alternative in terms of performance, cost, availability, and environmentally friendly when compared to already exiting CS aggregates and NFA. © 2021, The Institution of Engineers (India).Item EXPERIMENTAL INVESTIGATIONS ON THE PROPERTIES OF CONCRETE CONTAINING PRE-SOAKED RECYCLED FINE AGGREGATE(Associated Cement Companies Ltd., 2022) Saha, S.; C, C.; Ganiger, M.S.; Sajjan, S.Recycled fine aggregate (RFA) becomes very significant and promising alternative materials for natural fine aggregate (river sand) to be used in the production of concrete. But, most of the past research works indicated higher water absorption capacity of RFA as one of the key factor to affect the properties of fresh concrete. Therefore, an experimental attempt has been made to address the issues related to water absorption capacity of RFA by soaking it in water for 24 hours prior to use as alternative fine aggregate for the production of the fresh concrete. Mechanical properties of concrete such as compressive strength, splitting tensile strength, and flexural strength, and durability properties such as resistance against acidic and alkaline environment, chloride permeability test for ordinary Portland cement (OPC) and Portland pozzolana cement (PPC) based concrete mixes made with soaked recycled fine aggregates (SRFA) are determined, and analysed. For OPC, and PPC based concrete, respectively 4.32, and 20.75 % in compressive strength at 28 days; 2.69, and 27.24 % increase in flexural strength; 6.38, and 40 % increase in splitting tensile strength at 28 days were observed for the concrete mixes with SRFA compared to the mixes with RFA. Experimental results indicated notable improvement of the mechanical, and durability properties of concrete mixes when recycled fine aggregates were soaked in water prior to use. © 2022, Associated Cement Companies Ltd.. All rights reserved.Item Performance and microstructural investigations of processed lateritic fine aggregates in blended cement mortars exposed to elevated temperatures(Emerald Publishing, 2023) Basavana Gowda, S.N.; Yaragal, S.C.; C, C.; Goudar, S.K.Purpose: In recent years, fire accidents in engineering structures have often been reported worldwide, leading to a severe risk to life and property safety. The present study is carried out to evaluate the performance of Ground Granulated Blast Furnace Slag (GGBS) and fly ash–blended laterized mortars at elevated temperatures. Design/methodology/approach: This test program includes the replacement of natural river sand with lateritic fine aggregates (lateritic FA) in terms of 0, 50 and 100%. Also, the ordinary Portland cement (OPC) was replaced with fly ash and GGBS in terms of 10, 20, 30% and 20, 40 and 60%, respectively, for producing blended mortars. Findings: This paper presents results related to the determination of residual compressive strengths of lateritic fine aggregates-based cement mortars with part replacement of cement by fly ash and GGBS exposed to elevated temperatures. The effect of elevated temperatures on the physical and mechanical properties was evaluated with the help of microstructure studies and the quantification of hydration products. Originality/value: A sustainable cement mortar was produced by replacing natural river sand with lateritic fine aggregates. The thermal strength deterioration features were assessed by exposing the control specimens and lateritic fine aggregates-based cement mortars to elevated temperatures. Changes in the mechanical properties were evaluated through a quantitative microstructure study using scanning electron microscopy (SEM) images. The phase change of hydration products after exposure to elevated temperatures was qualitatively analyzed by greyscale thresholding of SEM images using Image J software. © 2023, Emerald Publishing Limited.Item Performance characteristics of self-compacting concrete containing lateritic fine aggregate as a partial replacement to natural river sand(Institute of Physics, 2024) Kiran Bhat, K.; C, C.; Das, B.B.This study identifies the use of processed lateritic fine aggregate (LFA) as a sustainable material for the replacement of natural fine aggregate (NFA) in self-compacting concrete (SCC). Cubes were cast with LFA replacements from 10% to 80% with an interval of 10% for checking the compressive strength development at 28 and 90 days. The findings demonstrate that the replacement of 30% NFA with LFA leads to the optimum performance, resulting in compressive strengths of 45.5 MPa and 53 MPa after 28 and 90 days of curing. Similar trends are also noted with the specimens cast for splitting tensile and flexural strengths as per IS 516: 2021. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), Thermogravimetric analysis (TGA), and Fourier Transform Infrared Spectroscopy (FTIR) were performed to understand the surface morphology, material characterization, and composition differences between the control mix (C30F) and optimized lateritic SCC (C30F30L). SEM and EDX analysis demonstrated the contribution of the introduced fly ash particles to the strengthening of concrete. TGA with DTA has shown the more complicated denser structure of the C30F mix, and FTIR has confirmed the presence and formation of the C-S-H gel. Si-O-Si asymmetric stretching band has extra peaks, and with FTIR, O-C-O asymmetrical bending and stretching wave band have a lower intensity than the C30F mix due to the partial replacement of LFA. In addition, it is also observed from the durability studies that C30F30L showed an increase in pore volume and capillary pore network compared to C30F mix. © 2024 The Author(s). Published by IOP Publishing Ltd.