Browsing by Author "Shenoy, S.U."

Now showing 1 - 7 of 7

Novel Co-Ni-graphene composite electrodes for hydrogen production
(2015) Subramanya, B.; Ullal, Y.; Shenoy, S.U.; Bhat, D.K.; Hegde, A.C.
Active, stable and cost-effective electrocatalysts are key to water splitting for hydrogen production through electrolysis. Herein, we report the facile preparation of highly porous Co-Ni-graphene (Co-Ni-G) composite electrodes by electrodeposition for electrocatalytic applications. The incorporation of graphene into the Co-Ni matrix enhances the catalyst's activity for the hydrogen evolution reaction (HER) in an alkaline solution. The best coating exhibits a maximum current density of -850 mA cm-2 at -1.6 V, which is approximately 4 times better than that of the binary Co-Ni alloy indicating higher activity for hydrogen production. The addition of graphene to an electrolyte bath results in a porous encapsulated bundle of alloy nano-particles within the graphene network which effectively increases the electrochemically active surface area. As indicated by XPS analysis results, on addition of graphene the Co(0) and Ni(0) content in the deposit increases and as a result both cobalt/cobalt oxide and nickel/nickel oxide sites are evenly distributed on the Co-Ni-G electrode surface which is responsible for increased HER activity. The Tafel slope analysis showed that the HER follows a Volmer-Tafel mechanism. The structure-property relationship of the Co-Ni-G composite coating has been discussed by interpreting field emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) analysis results. The Royal Society of Chemistry 2015.
Novel Co-Ni-graphene composite electrodes for hydrogen production
(Royal Society of Chemistry, 2015) Subramanya, B.; Ullal, Y.; Shenoy, S.U.; Bhat, D.; Hegde, A.C.
Active, stable and cost-effective electrocatalysts are key to water splitting for hydrogen production through electrolysis. Herein, we report the facile preparation of highly porous Co-Ni-graphene (Co-Ni-G) composite electrodes by electrodeposition for electrocatalytic applications. The incorporation of graphene into the Co-Ni matrix enhances the catalyst's activity for the hydrogen evolution reaction (HER) in an alkaline solution. The best coating exhibits a maximum current density of -850 mA cm-2 at -1.6 V, which is approximately 4 times better than that of the binary Co-Ni alloy indicating higher activity for hydrogen production. The addition of graphene to an electrolyte bath results in a porous encapsulated bundle of alloy nano-particles within the graphene network which effectively increases the electrochemically active surface area. As indicated by XPS analysis results, on addition of graphene the Co(0) and Ni(0) content in the deposit increases and as a result both cobalt/cobalt oxide and nickel/nickel oxide sites are evenly distributed on the Co-Ni-G electrode surface which is responsible for increased HER activity. The Tafel slope analysis showed that the HER follows a Volmer-Tafel mechanism. The structure-property relationship of the Co-Ni-G composite coating has been discussed by interpreting field emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) analysis results. © The Royal Society of Chemistry 2015.
Simple glucose reduction route for one-step synthesis of copper nanofluids
(Springer Nature, 2014) Shenoy, S.U.; Nityananda Shetty, A.
One-step method has been employed in the synthesis of copper nanofluids. Copper nitrate is reduced by glucose in the presence of sodium lauryl sulfate. The synthesized particles are characterized by X-ray diffraction technique for the phase structure; electron diffraction X-ray analysis for chemical composition; transmission electron microscopy and field emission scanning electron microscopy for the morphology; Fourier-transform infrared spectroscopy and ultraviolet–visible spectroscopy for the analysis of ingredients of the solution. Thermal conductivity, sedimentation and rheological measurements have also been carried out. It is found that the reaction parameters have considerable effect on the size of the particle formed and rate of the reaction. The techniques confirm that the synthesized particles are copper. The reported method showed promising increase in the thermal conductivity of the base fluid and is found to be reliable, simple and cost-effective method for preparing heat transfer fluids with higher stability. © 2012, The Author(s).
Synthesis of copper nanofluids using ascorbic acid reduction method via one step solution phase approach
(2012) Shenoy, S.U.; Nityananda, Shetty, A.
A simple one step solution phase approach to synthesize copper nanofluids has been developed, involving simultaneous in situ synthesis of nanoparticles and their dispersion in the base fluid. Copper nitrate has been reduced using ascorbic acid in ethylene glycol under thermal as well as microwave conditions. Sodium lauryl sulfate has been used to control the size of the particle as well as to act as a stabilizing agent. The effect of ratio of the reactants, pH, power of microwave, reaction time, and dilution on the size of the particles has been studied using X-ray diffraction, transmission electron microscopy, and field-emission scanning electron microscopy. The characterization of the fluids has also been done using Fourier transform infrared spectrometry, ultraviolet-visible spectroscopy, selected area electron diffraction, and energy dispersive X-ray analysis. The thermal conductivity and viscosity of the fluid were also measured at various particle concentrations. The copper particles in the fluid were found to have size less than 50nm and were well dispersed in the fluid. Thus this method was found to preserve the advantages of the polyol process and aqueous chemical reduction method as well. The fluid was stable up to 5 weeks under stationary conditions at room temperature. This method employs fast, inexpensive, extendible process for the synthesis of copper nanofluids and also overcomes the drawbacks of two step process. Copyright 2012 by ASTM International.
Synthesis of copper nanofluids using ascorbic acid reduction method via one step solution phase approach
(2012) Shenoy, S.U.; Nityananda, Shetty, A.
A simple one step solution phase approach to synthesize copper nanofluids has been developed, involving simultaneous in situ synthesis of nanoparticles and their dispersion in the base fluid. Copper nitrate has been reduced using ascorbic acid in ethylene glycol under thermal as well as microwave conditions. Sodium lauryl sulfate has been used to control the size of the particle as well as to act as a stabilizing agent. The effect of ratio of the reactants, pH, power of microwave, reaction time, and dilution on the size of the particles has been studied using X-ray diffraction, transmission electron microscopy, and field-emission scanning electron microscopy. The characterization of the fluids has also been done using Fourier transform infrared spectrometry, ultraviolet-visible spectroscopy, selected area electron diffraction, and energy dispersive X-ray analysis. The thermal conductivity and viscosity of the fluid were also measured at various particle concentrations. The copper particles in the fluid were found to have size less than 50nm and were well dispersed in the fluid. Thus this method was found to preserve the advantages of the polyol process and aqueous chemical reduction method as well. The fluid was stable up to 5 weeks under stationary conditions at room temperature. This method employs fast, inexpensive, extendible process for the synthesis of copper nanofluids and also overcomes the drawbacks of two step process. Copyright 2012 by ASTM International.
Synthesis of copper nanofluids using ascorbic acid reduction method via one step solution phase approach
(ASTM International, 2012) Shenoy, S.U.; Nityananda Shetty, A.N.
A simple one step solution phase approach to synthesize copper nanofluids has been developed, involving simultaneous in situ synthesis of nanoparticles and their dispersion in the base fluid. Copper nitrate has been reduced using ascorbic acid in ethylene glycol under thermal as well as microwave conditions. Sodium lauryl sulfate has been used to control the size of the particle as well as to act as a stabilizing agent. The effect of ratio of the reactants, pH, power of microwave, reaction time, and dilution on the size of the particles has been studied using X-ray diffraction, transmission electron microscopy, and field-emission scanning electron microscopy. The characterization of the fluids has also been done using Fourier transform infrared spectrometry, ultraviolet-visible spectroscopy, selected area electron diffraction, and energy dispersive X-ray analysis. The thermal conductivity and viscosity of the fluid were also measured at various particle concentrations. The copper particles in the fluid were found to have size less than 50nm and were well dispersed in the fluid. Thus this method was found to preserve the advantages of the polyol process and aqueous chemical reduction method as well. The fluid was stable up to 5 weeks under stationary conditions at room temperature. This method employs fast, inexpensive, extendible process for the synthesis of copper nanofluids and also overcomes the drawbacks of two step process. Copyright © 2012 by ASTM International.
Synthesis of copper nanofluids using ascorbic acid reduction method via one step solution phase approach
(2012) Shenoy, S.U.; Nityananda Shetty, A.N.
A simple one step solution phase approach to synthesize copper nanofluids has been developed, involving simultaneous in situ synthesis of nanoparticles and their dispersion in the base fluid. Copper nitrate has been reduced using ascorbic acid in ethylene glycol under thermal as well as microwave conditions. Sodium lauryl sulfate has been used to control the size of the particle as well as to act as a stabilizing agent. The effect of ratio of the reactants, pH, power of microwave, reaction time, and dilution on the size of the particles has been studied using X-ray diffraction, transmission electron microscopy, and field-emission scanning electron microscopy. The characterization of the fluids has also been done using Fourier transform infrared spectrometry, ultraviolet-visible spectroscopy, selected area electron diffraction, and energy dispersive X-ray analysis. The thermal conductivity and viscosity of the fluid were also measured at various particle concentrations. The copper particles in the fluid were found to have size less than 50nm and were well dispersed in the fluid. Thus this method was found to preserve the advantages of the polyol process and aqueous chemical reduction method as well. The fluid was stable up to 5 weeks under stationary conditions at room temperature. This method employs fast, inexpensive, extendible process for the synthesis of copper nanofluids and also overcomes the drawbacks of two step process. Copyright © 2012 by ASTM International.