Browsing by Author "Narkhede, A."

Filter results by typing the first few letters
Now showing 1 - 3 of 3
  • No Thumbnail Available
    Item
    3D Numerical Modelling of Turbulent Flow in a Channel Partially Filled with Different Blockage Ratios of Metal Foam
    (Isfahan University of Technology, 2024) Narkhede, A.; Gnanasekaran, N.
    The aim of the present research work is to understand the intricacies of fluid flow through a rectangular channel that has been partially filled with a metal foam block of different blockage ratio (0.16-1), with a pore density (5-30 Pores Per Inch i.e. PPI), along with varying inlet velocity (6.5-12.5 m/s). For the porous region, numerical solutions are acquired using the Darcy Extended Forchheimer model. The Navier-Stokes equation is used in the non-porous zone. Different flow behaviours were seen as a function of PPI, height, and inlet velocity. The pressure drop increases with inlet velocity, PPI, and block height, with a maximum value of approximately 4.5 kPa for the case of 30 PPI, 12.5 m/s, and a blockage ratio of 1. Results show that the existence and location of the formation of eddies depends on the inlet velocity, PPI, and blockage ratio. Such studies have been reported less and will aid research on forced convection through a channel partially filled with metal foam and optimisation studies between increased heat transmission and the additional pressure drop for the same by providing a detailed fluid flow analysis. © (2024), (Isfahan University of Technology). All Rights Reserved.
  • No Thumbnail Available
    Item
    A novel optimized liquid cooled heat sink integrated with 3D lattice structure under different blockage ratios
    (Elsevier Ltd, 2025) Narkhede, A.; Gnanasekaran, N.; Yadav, A.K.
    In this numerical work, investigation is focused on thermo-hydraulic nature of a periodic metal foam-integrated heat sink with an octet lattice-structure topology. Heat sink is partially filled with octet structure based periodic metal foam having 2.5 mm unit cell length with blockage ratios of 0.25/0.5/0.75/1, porosity of 0.83/0.87/0.91, and flow velocity of 0.02–0.05 m/s for electronic thermal management. The effect of porosity and blockage ratio on the wall temperature and pressure gradient of the heat sink is examined. Among all configurations, the lowest value of wall temperature of 311.24 K and the highest value of pressure gradient of 5091 Pa/m are observed for the case of blockage ratio 1, porosity 0.83, and flow velocity of 0.05 m/s. Additionally, the thermo-hydraulic performance enhancement owing to the partly packed configuration is observed based on the enhancement ratio and thermo-hydraulic performance parameter (THPP). The highest enhancement ratio is observed for the case with a blockage ratio of 1, porosity of 0.83, and a velocity of 0.02 m/s. The thermal design with a velocity of 0.03 m/s, a blockage ratio of 0.75, and a porosity of 0.83 is considered the optimal design in accordance with the THPP, which has a value of approximately 1.7. © 2025 Elsevier Ltd
  • No Thumbnail Available
    Item
    Detailed thermo-hydraulic investigation of 3D octet lattice structure integrated heat sink
    (Elsevier Ltd, 2025) Narkhede, A.; Gnanasekaran, N.; Yadav, A.K.
    The present research work examined the thermo-fluidic characteristics of a heat sink packed with octet-structured periodic metal foam having varying porosity (0.83–0.93) and unit cell lengths (UCL) of 2.5–5 mm for electronic cooling application. AlSi10Mg material is considered for the octet lattice structure with water as the cooling medium, with the inlet velocity ranging from 0.02 to 0.05 m/s and a steady heat flux of 10 W/cm2 applied at base of the substrate. The effect of the porosity, unit cell length, and inlet velocity on pressure gradient, friction factor, Nusselt number, wall temperature, heat transfer coefficient, and thermo-hydraulic performance parameter is analyzed. Larger pressure gradients are observed for lower values of porosity and unit cell length, with a maximum value of approximately 5000 Pa/m for the thermal system having 0.83 porosity, 2.5 mm UCL, and 0.05 m/s inlet velocity. The wall temperature drops with a rise in inlet velocity and a reduction in porosity and UCL, with the lowest value of 311 K for the case of 0.83 porosity, 2.5 mm UCL, and 0.05 m/s inlet velocity. The case of 0.83 porosity, 5 mm UCL, and 0.02 m/s velocity was determined as optimum design based on thermo-hydraulic performance parameter. © 2024